Atlona AT-VCC-RELAY Скачать руководство пользователя страница 19

Страница: 19 / 22

AT-VCC-RELAY

Control

Ensure all devices are set to their side of the room. When using a switcher, the inputs can be set within the

switcher menu.

3 Select Room Options from the top right. A menu will open on the left side of the screen.
4

Scroll down to the Control Page Layout section and Select the Enable Split Room slider. A new option will appear

below. Enable the Is room currently split if the room is currently set up as split, this is not required for setting up

the rest of the control.

1 Set up the room with all the devices.

A big use of the Room Triggers is for Split Rooms. This will provide a way to automate rooms when sensors are

triggered by opening and closing of a room divider and much more.

Split Rooms

NOTE:

If a device is set to All Sections, when

the room is split, either side of the room can

control that device. It is best to set to one

section so neither presenter will accidently

control the wrong source.

NOTE:

Connect the sensor of the VCC-Relay

to the room divider, so that when the divider

is opened and closed it will complete or break

the circuit.

Содержание AT-VCC-RELAY























Результаты поиска

Содержание AT-VCC-RELAY

Отзывы:

Бренды по названию

Популярные бренды

Atlona AT-VCC-RELAY, Руководство пользователя

Результаты поиска

Содержание AT-VCC-RELAY

Отзывы:

Бренды по названию

Популярные бренды