Atlona AT-PROHD82M Скачать руководство пользователя страница 9

www.atlona.com | toll free: 

1-877-536-3976

For International: 1-

408-962-0515

9

RS232

The Atlona AT-PROHD82M switcher can be controlled via the RS-232 serial control port to allow for interfacing 

to a PC, or similar third party control system.

The serial communication parameters are 9600 baud, 8 bit no parity and 1 stop bit. This is often referred to 

as 9600 8N1. When the unit recognizes a complete command it will perform the requested action. There is no 

delimiter character required. 

The unit does not send out a message when a value is changed from the front panel or by IR control. If the 

switcher needs to be controlled in addition to the RS-232 control, you should regularly verify the unit’s status to 

ensure the control system accurately reflects the current settings.

1. Protocol Commands

To switch Inputs to Outputs

SBI0XO0Y

 – Where X is

,QSXW

 Number (1-8) and Y is 

2XWSXW

 Number (1-2)

Unit will respond with:

SBUD0XOY

 – Where X is Output Number (1-2) and Y is Input Number (1-8)

Example: Send Input 7 to Output 2

SBI07O02

 – Sending Command

SBUD07O2

 – Would be feedback command which switcher will send back to the control system to confirm the 

input change. Command received.

Note: Turning the unit System Power Off over RS-232 will extinguish the LED channel display leaving only the 

Power Switch LED on. The Video and Audio outputs will also mute. While the unit is turned off by RS0-232 it 

will continue to accept and act upon switching commands. For example, if the unit is in the off mode (via RS-

232) and you send a command to switch an input to an output, that route will complete and the video and audio 

will now appear on that channel only. The front panel LED channel display for that particular output will also 

show the input selected (for that single output channel only). 

The remaining LED’s will remain off and video and audio outputs muted. The unit will still return status 

and change messages in response to commands sent while in Power Off state. A hard reset command 

(SBALLRST) will return the unit to normal operation and also unlock the front panel.

Power OFF Command: 

SBSYSMOF

Power ON Command: 

SBSYSMON

Unit will respond with:

Unit is in Standby mode: 

SBALOFAK

Unit is no longer in Standby mode: 

SBALONAK

Example: Put unit in Standby (Soft Power) 

SBSYSMOF

 

    Switcher will have feedback with 

SBALOFAK

 RS 232  SERIAL COMMANDS

Содержание AT-PROHD82M













Отзывы: