Atlas Copco GA 11 VSD Скачать руководство пользователя страница 73

Страница: 73 / 84

7.5

Safety valves

Location of safety valve

Safety valve on oil vessel

Operating

Operate safety valve (SV) by unscrewing the cap one or two turns and retightening it.

On Tank-mounted compressors, also operate safety valve (SV1) by unscrewing the cap one or
two turns and retightening it.

Testing

Before removing the valves, stop and depressurise the compressor. See section

Problem solving.

Valve (SV) can be tested on a separate air line. If the valve does not open at the set pressure
stamped on the valve, the valve must be replaced.

Valve (SV1) is fitted on Tank-mounted versions. The valve can be tested on a separate air line. If
the valve does not open at the set pressure stamped on the valve, the valve must be replaced.

Warning

No adjustments are allowed. Never run the compressor without safety valve.

Instruction book

API161475

Содержание GA 11 VSD





















































































Результаты поиска

Содержание GA 11 VSD

Отзывы:

Бренды по названию

Популярные бренды

Atlas Copco GA 11 VSD, Инструкция

Результаты поиска

Содержание GA 11 VSD

Отзывы:

Бренды по названию

Популярные бренды