Atlantic alfea excellia duo 11 Скачать руководство пользователя страница 20

Страница: 20 / 68

Liquid

valve

Flare

nut

Flare

nut

Flare

nut

“Liquid” refrigeration connection

diameter D2

“Gas” refrigeration connection

diameter D1

Gas

valve

Flare

nut

Outdoor

unit

Hydraulic

unit

figure 21 - connection of thre refrigerating connectors (authorised diameters and lengths - in metres)

2 .7 .5

Connecting the flare connections

The connections must be made the day the gas

is connected to the installation (see §

2.8, page

Pay special attention to the position of the tube

aligned with its connector to avoid damaging

the thread . A correctly aligned connector can be

fitted easily by hand without much force being

required .

The refrigerating circuit is very sensitive to dust

and humidity, check that the zone around the

connection is dry and clean before removing the

plugs that protect the refrigerating connectors .

Remove the plugs from the pipes and refrigerating

connections

Place the tube in front of the flare connector and

screw on the nut by hand, holding the connector with a

spanner, until contact is made.

Respect the tightening torques stated (see

figure 20,

page 19

)

PAC Model

alféa hybrid duo oil single phase and three phase

Gas

Liquid

Outdoor unit connectors

5/8"

3/8"

Refrigerating

connections

Diameter

(D1) 5/8"

(D2) 3/8"

Minimum length (L)

Maximum * length (L)

Maximum ** height difference (D)

Hydraulic module connectors

5/8"

3/8"

: without additional volume of R410A

: take into account any additional volume (see

2.8.3, page 22

)

Installation and operating manual

1605 - EN

alfea hybrid duo heat pump oil low NOx CH

- 20 -

Содержание alfea excellia duo 11





































































Результаты поиска

Содержание alfea excellia duo 11

Отзывы:

Похожие инструкции для alfea excellia duo 11

Бренды по названию

Популярные бренды

Atlantic alfea excellia duo 11, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание alfea excellia duo 11

Отзывы:

Похожие инструкции для alfea excellia duo 11

Бренды по названию

Популярные бренды