Atlanta Attachment Company 1345-4B Скачать руководство пользователя страница 58

Страница: 58 / 90

Technical Manual & Parts Lists

4
5

Installation of Footlift Link & Handle

Tools Required

(1) 7/16” wrench

(1) 7mm wrench

(1) 8mm wrench

(1) 9mm wrench

(1) 7/64” allen wrench

(1) 1/8” allen wrench

Installation

If not already installed, mount the pivot bracket (1345-503)

to the sewing head as shown using the 1/4-20 bolts and washers provided. Center the

slots on the bolts ensure the bracket is parallel to the sewing surface.

Place one stop collar (1345077) onto the pivot arm (1345-504) and insert the pivot arm

into the barrel of the pivot bracket as shown. Place another stop collar onto pivot arm
as shown.

Place the collar/link (1349518) on the pivot arm aligning the

two set screws in the collar with the two flat surfaces on

the pivot arm shaft. Tighten the two set screws.

Push the pivot arm until the collar/link is touching the

bearing surface on the pivot bracket. Then, snug the stop

collar, on the other side, against the other bearing surface
on the pivot bracket. Be sure the stop does not prevent

the handle from turning upwards approximately 90

degrees on the handle side.

Place one of the two threaded studs of the linkage (included

in accessory box) into the hole at the end of the
collar/link. Put the other threaded stud into the hole

located in the footlift lever. Place and tighten the two hex

nuts.

Adjustments

The following adjustments should be made to achieve

maximum footlift while the handle is able to stay in the up
position without being held.

Lengthen the linkage by turning the rod until the handle is

just able the stay in the up position. Tighten the lock nuts

on each end of the rod.

Turn the right stop collar until the stop hits the pivot bracket

in order to prevent the handle from turning more than is

necessary for it to stay in the up position.

Adjust the left stop collar so that the handle stops in the

down position.

Содержание 1345-4B



























































































Результаты поиска

Содержание 1345-4B

Отзывы:

Похожие инструкции для 1345-4B

Бренды по названию

Популярные бренды

Atlanta Attachment Company 1345-4B, Техническое руководство и перечень запасных частей

Результаты поиска

Содержание 1345-4B

Отзывы:

Похожие инструкции для 1345-4B

Бренды по названию

Популярные бренды