ATI Technologies MetriNet Q52 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 51

ATI Technologies MetriNet Q52 Скачать руководство пользователя страница 23

23

O&M Manual
Rev-C (05/20)

Part 4 – Operation

4.1

General

Check to see that sample is running through the flow assembly.  Sample flow is controlled at 200
ml./min.  If  the  system  was  not  purchased  with  the  flow  control  element,  adjust  the  flow  through
the system with  a valve placed on the outlet side of the flow assembly.    Recheck all wiring and
verify that the power supply is in the range of 12-24 VDC for external DC systems, and 12VDC for
battery systems.  Note that battery powered systems will run from 12VDC down to about 7 VDC.
The controller does not contain a power switch.  It will operate as soon as DC power is applied.
Once power is applied, the system will go through an initialization routine and then will begin to
operate.

4.2

Controller Interface

The user interface for the MetriNet controller consists of a custom display and a membrane
keypad. All functions are accessed from this user interface.

Figure 15

– MetriNet Controller Interface

MENU ICONS

UNITS

12-CHARACTER

SECONDARY

DISPLAY

MEMBRANE

KEYPAD

MENU

ESC

ENTER

A

B

DIAG

FAIL

HOLD

CAL

CONF

MENU ICONS

UNITS

12-CHARACTER

SECONDARY

DISPLAY

MEMBRANE

KEYPAD

ENTER KEY

LEFT ARROW

KEY

4-DIGIT

MAIN DISPLAY

MENU/ESCAPE

KEY

UP ARROW

KEY

SIGN

RELAY/LO-BAT

INDICATOR

4-KEY USER

INTERFACE

RELAY

INDICATOR

«
...
21
22
23
24
25
...
»

Содержание MetriNet Q52




















































Отзывы:

Нет отзывов