M
3
QUICK START + OPERATION
MACHINE DIAGRAM
GENERAL OPERATION
TOP VIEW
MACHINE ORIENTATION
HITTER
OPERATOR
1
- On/Off Switch
2
- Speed Control
3
- Speed Chart
4
- Ball Chute
5
- Wheels
6
- Fuse Box
7
- Frame
8
- Vertical Adjustment Handle
9
- Horizontal Adjustment Handle
10
- Front Wheel Guard
11
- Top Wheel Guards
12
- Fungo Handle
1
7
11
11
12
1.
Place the machine the desired pitch distance from home plate.
*Recommended machine distance is 50-60 feet
2.
Position legs so that two are directed toward the plate & one is back, toward the
operator (see
Machine Orientation
).
3.
Check that the On/Off Switch (
1)
is set to the “off” position.
4.
Standing behind the machine, plug your M3 into a 110 volt power source.
*Always use a 3-prong plug & 16 gauge or heavier power cord.
5.
Always use a Protective Screen for the safety of the operator.
6.
Aim the machine at the approximate pitch direction using the Horizontal and Vertical
Adjustment Handles (8 & 9) and tighten the handles to secure the machines position.
7.
Turn the machine On and set Speed Control Knobs (
2
) to the desired speed setting.
Refer to the Speed Chart (3) for guidance on proper settings. Allow the motors time to
reach the proper speed before feeding a ball.
8a.
Test the pitch location by feeding a ball into the Ball Chute (
4
). Confirm pitch’s location
multiple times before allowing a batter to step into the box.
8b.
Make adjustments to the machines orientation as needed, and tighten all handles
after any adjustments are made. Test pitch location after all adjustments.
9.
Always set the speed and type of pitch to a level consistent with the ability, experience,
and comfort level of the batter.
10.
Always alert the batter verbally or with a routine visual signal and wait for an
acknowledgement from the batter prior to pitching the ball.
11.
Never mix balls types in a single training session. Mixing brands, types of balls, or
balls with different degrees of wear/age will negatively affect the consistency and
accuracy of the machine.
12.
When adjusting your machine, always loosen the appropriate Adjustment Handles
before moving the machine as desired, then tighten.
1.
Position machine head aimed at center of home plate
2.
Consult speed setting chart for appropriate speed settings for specific pitch and batter ability. Set
wheel speeds accordingly.
3.
Aim the machine and test the pitch location. Continue to make adjustments as needed using left/right
and vertical adjustment handles, and always test the pitch location before letting a hitter enter the
batter’s box.
1.
Consult speed setting chart for appropriate speed settings for specific pitch (curve/slider/etc) and batter
ability. Set wheel speeds accordingly.
2.
Raise the pitch height by turning the vertical adjustment handle (8)clockwise. This will allow room for
the pitch to break down into the strike zone.
3.
Loosen the horizontal adjustment handle (9), move machine right of center to desired pitch placement.
4.
Tighten the horizontal adjustment handle (9) by turning it clockwise. This will secure the machine’s
left/right rotation.
5.
Aim the machine and test the pitch location. Continue to make adjustments as needed and always test
the pitch location before letting a hitter enter the batter’s box.
1.
Remove tripod assembly and tripod leg sections from box
2.
Assemble tripod legs, and connect into tripod assembly. Check that snap locks have secured in place
at all connection points
3.
Place the machine tripod in desired location to operate the machine. Position the legs
s
o that two are
directed towards the direction of the ball flight, and one is back, towards the operator
4.
With machine head on the ground, check that the locking pin is securely fastened
5.
With a partner, one on each side of the machine, lift the machine up and slide frame onto tripod spindle.
6.
Tighten the horizontal adjustment handle (9) by turning it clockwise. This will secure the machine’s
left/right rotation.
7.
See "OPERATION" instructions to begin using your machine
FASTBALL
FASTBALL to RH BREAKING BALL
1.
Consult speed setting chart for appropriate speed settings for specific pitch (curve/slider/etc) and batter
ability. Set wheel speeds accordingly.
2.
Raise the pitch height by turning the vertical adjustment handle (8) clockwise. This will allow room for the
pitch to break down into the strike zone.
3.
Loosen the horizontal adjustment handle (9), move machine left of center to desired pitch placement.
4.
Tighten the horizontal adjustment handle (9) by turning it clockwise. This will secure the machine’s
left/right rotation.
5.
Aim the machine and test the pitch location. Continue to make adjustments as needed and always test
the pitch location before letting a hitter enter the batter’s box.
FASTBALL to LH BREAKING BALL
MACHINE ASSEMBLY
2
5
3
4
5
6
9
8
10
