Atec 6275 KWIKSTART, Руководство пользователя

Страница: 2 / 4

2
NOTE: first
gh
the KWIKSTART
could be damaged due to overcharging.
1.
gh a
g
The
d. he red LED goes off and
e. y
charger remain connected to an AC power source whenever the
2.
he test
OVERCHARGE! This is not an automatic method of charging the
KWIKSTART. Overcharging will damage your KWIKSTART.
CTIONS
t it will not start the vehicle without assistance. However, the
WIKSTART can also be used to restore some charge to the vehicle
. Plug the power extension cord from the KWIKSTART into the
OTE: Some vehicle’s ignition keys must be turned to accessory to
OTE: A defective battery may refuse to accept a charge from the
MERGENCY JUMP STARTER
0°F when using
fore making cable connections.
3.
he vehicle frame (ground).
moving belts or fan.
8. Sta
NOTE:
ry cool for 3 minutes before
START may occur.
the vehicle frame.
2. Return jumper cables to their stored position.
. However, if
e power extension cord is plugged from the KWIKSTART to the cigar
s OBD2 connector to save all memory functions. The
MS6209 memory saver may be purchased separately for these
applications.
FEATURES
1. Provides plenty of power for starting vehicles. More than enough to
start most vehicles. May also be used in DEEP CYCLE
applications.
2. The KWIKSTART will power most 12 VDC accessories equipped
with a male cigar lighter plug. The DC outlet has automatic overload
protection.
3. Test switch and Multiple LED power level indicators. State of the art
charging circuit.
4. ON/OFF switch. When in the OFF position, no voltage will be
present at the clamps, reducing the chance of arcing.
INFORMATION TO USER
Changes or modifications by the user, that are not expressly approved
by the party responsible for radio frequency emmission levels from the
KWIKSTART, could cause an undesirable amount of radio frequency
energy to be emitted. Such action could void the user's authority to use
the KWIKSTART.
SAFETY FEATURES
1. Selector switch prevents accidental sparking of clamps.
2. Cable bracket hold the cables for clean storage. (No unsightly
dangling wires).
3. The KWIKSTART contains the latest technology with its 2 -12 volt
sealed non-spillable batteries. The KWIKSTART may be stored in
any position.
RECHARGING PROCEDURES
When new, your KWIKSTART should be charged for a minimum of 30
hours, unless the green High power level LED lights when the test
button is pressed. (See Figure 2)
Figure 2.
ON/OFF switch, test button, power level LED’s, internal charger plug
There are two ways to recharge the KWIKSTART. The
method is automatic charging with the internal charger
(preferred). The second is through the DC power jack throu
the DC power extension cord. The second method is not
automatic and requires watching because
USING THE INTERNAL CHARGER: The KWIKSTART is
automatically charged using the internal charger. A two pin male
plug on the KWIKSTART’s control panel is connected throu
smart circuit board to the KWIKSTART making rechargin
automatic. Recharging takes approximately 24 hours.
Overcharging is not a problem when using the internal charger.
KWIKSTART’s internal charger can be left connected to an AC
power source indefinitely.
a. Turn the ON/OFF switch to OFF.
b. Connect an extension cord to the KWIKSTART’s male plug.
Plug the extension cord into a co c. rrectly wired AC receptacle (the
red CHARGING LED will light).
The battery will be fully charged when t
the green CHARGED LED comes on.
If you are not going to need the KWIKSTART right away you ma
leave the KWIKSTART’s internal charger connected to the AC
power source. We recommend that the KWIKSTART’s internal
KWIKSTART is not in use.
USING THE DC POWER EXTENSION CORD. Plug one end of the
power extension cord into the KWIKSTART power receptacle and
the other end into a vehicle’s lighter outlet (vehicle’s engine should
be running first). Turn the ON/OFF switch to ON. Push t
button
once every hour to check the power level. When the High
power level LED lights the battery is charged. DO NOT
OPERATING INSTRU
USED AS A BATTERY CHARGER
The KWIKSTART is intended, primarily, to be used to start or restart a
vehicle when the battery in the vehicle has become run down to the
point tha
K
battery.
1
vehicle’s cigar lighter outlet for 30 minutes.
N
activate the cigar light socket.
2. Remove the power extension cord and start the car.
N
KWIKSTART.
USED AS AN E
NOTE: For optimum performance, do not store below 5
as a jump starter.
1. Turn ignition off be
2. Use in a well ventilated area.
SHIELD EYES.
4. Clamp the positive (red +) clamp to the positive terminal on the
weak battery (for negative ground system).
5. Clamp the negative (black –) clamp to t
Make sure the cables are not in the path of
6. Switch the ON/OFF switch to the ON.
7. Stay clear of batteries while jump starting.
rt the vehicle (turn on the vehicle ignition).
If the vehicle does not start within 6 seconds, let the
KWIKSTART internal batte
attempting to start the vehicle again or damage to the
KWIK
9. When the vehicle is started, turn the selector switch to the OFF
position.
10. Disconnect the negative (-) battery clamp from
11. Disconnect the positive (+) clamp.
1
13. Recharge at earliest convenience.
USED AS AN ALTERNATIVE POWER SUPPLY FOR
VEHICLES
The KWIKSTART is an essential tool for all who replace automobile
batteries. Most vehicles have some type of electronic component with
memory, such as alarm systems, computers, radios, phones, etc…
and when the vehicle’s battery is replaced, memory is lost
th
lighter outlet on the vehicle, the memories can be saved.
NOTE: Some vehicles may require the KWIKSTART to be connected
to the vehicle’