Error Messages
Error Messages
Error Messages
Error Messages
The following messages alert the user when an operation has failed.
The battery is low.
The prism temperature is below the temperature range.
The ZERO button was pressed with nothing or something
other than water on the prism.
The prism temperature is above the temperature range.
The START button was pressed with nothing or an
insufficient amount of sample on the prism.
The instrument is faulty. (Replace the batteries. Contact
ATAGO if this error persists.)
The sample measured outside the measurement range.
Too much light is entering the prism, and the instrument
cannot measure accurately. (Shade the sample stage with
your hand and take a measurement again.)
Automatic Temperature Compensation
Automatic Temperature Compensation
Automatic Temperature Compensation
Automatic Temperature Compensation
The readings are corrected, based on the temperature of the prism, within the automatic temperature compensation range.
【Caution】
◇
Measurements may fluctuate with hot or cold samples. Wait for approximately 20 seconds to press the START button. Measurements will stabilize
once the instrument acclimates to the sample temperature.
Storage and Maintenance
Storage and Maintenance
Storage and Maintenance
Storage and Maintenance
Store the instrument in a dry
place away from direct
sunlight. Exposure to
humidity and heat may
damage the instrument.
Do not use organic solvents
(paint thinner, benzene,
gasoline, etc.) on the plastic
body case.
Clean and dry the sample stage
thoroughly, following the
“
Cleaning
”
instructions.
Store the unit away from direct
sunlight at a stable temperature with
as little fluctuation as possible.
Repair and Warranty
Repair and Warranty
Repair and Warranty
Repair and Warranty
The instrument is warranted for one year from the date of purchase. This warranty is void if the instrument shows evidence of the following. Send the
included batteries as well if they are still in use.
•
Having been disassembled by unauthorized personnel
•
Damages to the prism and/or sample stage
•
Water damage or having been dropped
•
Having been misused and/or operated outside the environmental specifications
•
Leakage from batteries other than those included with the unit
Repair services are available for a fee after the warranty expires. Contact an ATAGO authorized service center for service and support.
Please have the serial number information ready when contacting a service center.
Specifications
Specifications
Specifications
Specifications
Measurement range
Cutting Oil 0.0 to 70.0
Sample volume
At least 0.3ml
Temperature 10.0 to 75.0℃
Measurement time
Approx. 3 seconds
Resolution
Cutting Oil 0.1
Temperature 0.1℃
Backlight
The backlight stays on for 30 seconds after
Accuracy
Cutting Oil ±0.2 Temperature ±1℃
any button is pressed.
Automatic temperature 10 to 75℃
Power supply
Two (2) AAA alkaline batteries
compensation range
Battery life
Approx. 11,000 measurements
Ambient temperature
10 to 40℃
(when using alkaline batteries)
range
International
IP65
Protection class
Dimensions and weight
55 (W) x 31 (D) x 109 (H)mm, 100g (main unit only)
The product is in conformity with the requirements of the EMC Directive 2004/108/EC.
Patent Granted in Japan, United States, Germany, China and Taiwan.
Headquarters: The Front Tower Shiba Koen,
23rd Floor 2-6-3 Shiba-koen, Minato-ku,
Tokyo 105-0011, Japan
TEL: 81-3-3431-1943 [email protected]
http://www.atago.net/
TEL: 1-425-637-2107
[email protected]
TEL: 91-22-2854-4915 / 4071-3232
[email protected]
TEL: 66-21948727-9 ,66-21171549
[email protected]
TEL: 55 16 3913-8400
[email protected]
TEL: 39 02 36557267
[email protected]
TEL: 86-20-38108256 [email protected]
TEL: 7-812-777-96-96 [email protected]
TEL: 234-707-558-1552 [email protected]
1602WP Printed in Japan
“
“
“
Pocket”
”
”
” Cutting
Cutting
Cutting
Cutting o
o
o
oil
il
il
il Refractometer
Refractometer
Refractometer
Refractometer
PAL
PAL
PAL
PAL----102S
102S
102S
102S
Cat.No.4502
4502-E12
Instruction Manua
Instruction Manua
Instruction Manua
Instruction Manuallll
Parts
Parts
Parts
Parts
Contents
Contents
Contents
Contents
Main unit......... 1
Instruction Manual (this book) .....1
Calibration Report .. 1
AAA batteries ...........2
AAA alkaline batteries are included. Remove the tape from the battery compartment before inserting the batteries.
ATAGO instruments are rigorously inspected to ensure each unit meets the highest standards of quality assurance.
Introduction
Introduction
Introduction
Introduction
Thank you for purchasing the instrument. Carefully read and follow all instructions. Keep this manual for future reference.
Safety
Safety
Safety
Safety Instructions
Instructions
Instructions
Instructions
Read and follow all safety instructions before operating the instrument. Failure to comply with the following instructions may result in personal injury or
property damage.
◇
Ensure safety when handling hazardous materials. Observe precautionary measures and use protective equipment, Be aware of the hazards of such
chemicals and emergency response guidelines.
◇
ATAGO may not be held liable for any injury or damage arising in connection with handling of hazardous materials during the use of the instrument.
◇
Do not drop the instrument or subject it to strong physical shock.
◇
Do not attempt to repair, modify, or disassemble the instrument.
◇
Carefully read this manual to have basic knowledge of the function of each component.
◇
ATAGO is not liable for any loss and damage caused by the measurement and use of this instrument.
◇
Some acids may corrode the glass prism and/or metal sample stage, which may cause erroneous measurements.
◇
Do not use metal tools, such as a spoon, as they may scratch the prism, resulting in erroneous measurements.
◇
Do not use water above 50℃ to rinse the instrument.
◇
Only use the specified battery type. Observe proper polarities, properly aligning the anodes and cathodes.
◇
Store the instrument away from direct sunlight/heat sources and excessive amounts of dust/debris.
◇
Do not expose the instrument to a rapid change in ambient temperature.
◇
Do not subject the instrument to strong vibration.
◇
Do not subject the instrument to extreme cold temperature.
◇
Do not place the instrument under anything heavy.
◇
Loosen the battery compartment cover for air transportation.
<
<
<
<International Protection Classification IP65
International Protection Classification IP65
International Protection Classification IP65
International Protection Classification IP65>
>
>
>
◇
The instrument is water-resistant, not waterproof, and should not be submerged.
<
<
<
<Chemical Resistance of Body Case
Chemical Resistance of Body Case
Chemical Resistance of Body Case
Chemical Resistance of Body Case>
>
>
>
◇
The body case is made of PBT resin. Do not expose it to water vapor or solvents. See the list of
“
Solvents Harmful to Body Case.
”
Solvents Harmful to Body Case
Solvents Harmful to Body Case
Solvents Harmful to Body Case
Solvents Harmful to Body Case
1,2-Dichloroethane／Dichloromethane
Solvents that are harmful to the plastic body case include but not limited to the above substances.
Apply water and samples on the glass prism located
in the center of the sample stage.
Sample stage
Lanyard hole
ZERO button
Press to perform zero-setting.
Measurement results, prism temperature,
and remaining battery charge are displayed.
The displayed value is an example.
Press to take measurements and hold down
to turn off the display.
Place and remove batteries from here.
LCD
Battery compartment
START button
