Asystems DMA8413 Скачать руководство пользователя страница 5

Страница: 5 / 24

DMA8825 / DMA8813 / DMA8425 / DMA8413

Mounting Holes

These holes are for mounting the DMA device on a

standard 19” rack.

Output Level Control Knob 1 – 8

(DMA8825/DMA8813)

or 1 -4

(DMA8425/DMA8413)

Every output channel is equipped with a rotary knob for

adjusting the final output level.

LED

Every input channel is equipped with a 4-segment IN

LED, plus with a CLIP/PORT indicator.

BRIDGE

LED

This LED lights when the channel is bridged with another

channel�

* Every input channel is equipped with 1 control knob,

LED and 1

BRIDGE

LED�

Cooling Inlet Vents

Cool air is drawn here�

Reset Button

A pinhole button is included, for resetting the DMA

device to the factory default values�

Indicators

POWER:

Lights when the device is on�

DISABLE:

Lights when the power switch is disabled.

STANDBY/UNLOCK:

Lights when DMA device is in the

Standby mode.

PROTECT:

Lights when the protect circuity is active�

Power Switch

Flick this switch to turn the unit on and enter it into

STANDBY mode.

WARNNING:

The DMA requires 2 minutes to be fully

discharged after the power is off, or it cannot power on

properly�

3. CONTROLS and I/O
FRONT PANEL

Содержание DMA8413

























Результаты поиска

Содержание DMA8413

Отзывы:

Похожие инструкции для DMA8413

Бренды по названию

Популярные бренды

Asystems DMA8413, Руководство пользователя

Результаты поиска

Содержание DMA8413

Отзывы:

Похожие инструкции для DMA8413

Бренды по названию

Популярные бренды