Asyril Asycube Скачать руководство пользователя

Страница: 37 / 41

Asycube - Asyril SA

Operating Manual

Maintenance and reparation

v1.7

FO 32.03.118

Operating Manual

Asycube

- Asyril SA

37/41

Cleaning bulk

4.3.4.

Material needed :

Lint-free cloth

isopropanol alcohol

allen key (1.5mm)

Step 1

Unscrew the six screw

(A)

of the

plexiglas lid

(B)

of the bulk

Step 2

Clean all interior surfaces of the

bulk

Figure 4-3 : Bulk

Control and Cleaning of the platform

4.3.5.

Material needed :

Lint-free cloth

isopropanol alcohol

Step 1

Control the surface state of the

platform

(A)

and be particulary

carefull to the folloying points :

Big claws

Dirt or spotted surface

Oily or greasy surface

WARNING :

If the surface is damaged so as to

obstruct vision or the behavior of

parts, its replacement must be

proceeded

Step 2

Clean the surface of the platform

Figure 4-4 : Platform

Cleaning 3D vibration module

4.3.6.

NOTE :

This maintenance operation can only be performed by a Asyril technician.

For more information on this operation, please contact

Asyril customer’s service.

Voicecoils control and audit of component behavior

4.3.7.

NOTE :

This maintenance operation can only be performed by a Asyril technician.

For more information on this operation, please contact Asyril customer’s service.

(B)

(A)

Содержание Asycube










































Результаты поиска

Содержание Asycube

Отзывы:

Похожие инструкции для Asycube

Бренды по названию

Популярные бренды

Asyril Asycube, Руководство по эксплуатации

Результаты поиска

Содержание Asycube

Отзывы:

Похожие инструкции для Asycube

Бренды по названию

Популярные бренды