Asus Vintage V2-PH2 Скачать руководство пользователя страница 83

Страница: 83 / 102

5-19

ASUS Vintage V2-PH2

5.4.2 JumperFree Configuration

Overclocking [Auto]

Allows selection of CPU overclocking options to achieve desired

CPU internal frequency. Select either one of the preset overclocking

conﬁguration options:

Manual - allows you to individually set overclocking parameters.
Auto - loads the optimal settings for the system.

Conﬁgure System Frequency/Voltage

Overclocking

[Auto]

Memory Clock Mode

[Auto]

Select the target CPU

frequency, and the

relevant parameters

will be auto-adjusted.

Frequencies higher

than CPU manufacturer

recommends are not

guaranteed to be

stable. If the system

FSB/CPU External Frequency Synchronization

Front Side Bus

CPU External Frequency

FSB 1066

266 MHz

FSB 800

200 MHz

FSB 533

133 MHz

The following item appears only when you set the Overclocking item to

[Manual].

CPU Frequency [XXX]

Displays the frequency sent by the clock generator to the system bus and

PCI bus. The value of this item is auto-detected by the BIOS. Use the <+>

and <-> keys to adjust the CPU frequency. You can also type the desired

CPU frequency using the numeric keypad. The values range from 100

to 400. Refer to the table below for the correct Front Side Bus and CPU

External Frequency settings.

Содержание Vintage V2-PH2







































































































Результаты поиска

Содержание Vintage V2-PH2

Отзывы:

Бренды по названию

Популярные бренды

Asus Vintage V2-PH2, Руководство пользователя

Результаты поиска

Содержание Vintage V2-PH2

Отзывы:

Бренды по названию

Популярные бренды