Asus P5SD1-FM2 страница 63 Скачать руководство пользователя

Страница: 63 / 77

ASUS P5SD1-FM2

2-19

2 . 4 . 3

Onboard Devices Configuration

Configure ITE8712 Super IO Chipset

Serial Port1 Address

[3F8/IRQ4]

Serial Port1 Mode

[Normal]

Parallel Port Address

[378]

Parallel Port Mode

[ECP]

ECP Mode DMA Channel

[DMA3]

Parallel Port IRQ

[IRQ7]

Onboard 1394 Controller

[Enabled]

Allows BIOS to enable
or disable the floppy
controller.

Serial Port1 Address [3F8/IRQ4]

Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3]

Serial Port1 Mode [Normal]

Allows you to select the Serial Port1 mode.
Configuration options: [Normal] [IrDA] [ASK IR]

COMA Duplex Mode [Half Duplex]

Allows the BIOS to select Full or Half Duplex for Serial Port. This
appears only when the

Serial Port1 Mode

item is set to [IrDA] or

[ASK IR] Configuration options: [Full Duplex] [Half Duplex]

Parallel Port Address [378]

Allows you to select the Parallel Port base addresses.
Configuration options: [Disabled] [378] [278]

Parallel Port Mode [ECP]

Allows you to select the Parallel Port mode.
Configuration options: [Normal] [EPP] [ECP] [EPP+ECP]

EPP Version [1.9]

Allows selection of the Parallel Port EPP version. This item appears
only when the

Parallel Port Mode

is set to [EPP] or [EPP+ECP].

Configuration options: [1.9] [1.7]

ECP Mode DMA Channel [DMA3]

Allows you to set the Parallel Port ECP DMA. This item appears only
when the

Parallel Port Mode

is set to [ECP] or [EPP+ECP].

Configuration options: [DMA0] [DMA1] [DMA3]

Parallel Port IRQ [IRQ7]

Allows selection of the Parallel Port IRQ.
Configuration options: [IRQ5] [IRQ7]

This Manual: http://www.manuallib.com/file/2595652

Содержание P5SD1-FM2














































































Результаты поиска

Содержание P5SD1-FM2

Отзывы:

Похожие инструкции для P5SD1-FM2

Бренды по названию

Популярные бренды

Asus P5SD1-FM2, Руководство пользователя

Результаты поиска

Содержание P5SD1-FM2

Отзывы:

Похожие инструкции для P5SD1-FM2

Бренды по названию

Популярные бренды