Asus CUW страница 34 Скачать руководство пользователя | Manualshive

Страница: 34 / 128

background image

34

ASUS CUW User’s Manual

Connectors

3. H/W SETUP

3. HARDWARE SETUP

10) Primary / Secondary IDE Connectors (40-1 pin PRIMARY/SECONDARY)

These connectors support the provided UltraDMA/66 IDE hard disk ribbon cable.
Connect the cable’s blue connector to the motherboard’s primary (recommended)
or secondary IDE connector, and then connect the gray connector to your
UltraDMA/66 slave device (hard disk drive) and the black connector to your
UltraDMA/66 master device. It is recommended that non-UltraDMA/66 devices
be connected to the secondary IDE connector. If you install two hard disks, you
must configure the second drive to Slave mode by setting its jumper accord-
ingly. Refer to your hard disk documentation for the jumper settings. BIOS now
supports specific device bootup (see Boot Sequence in 4.6 Boot Menu).

(Pin

20 is removed to prevent inserting in the wrong orientation when using
ribbon cables with pin 20 plugged). If you have more than two UltraDMA/66
devices, you will need to purchase another UltraDMA/66 cable.
NOTE: A small hole near the blue connector on the UltraDMA/66 cable is in-
tentional.
TIP: You may configure two hard disks to be both Masters with two ribbon
cables – one for the primary IDE connector and another for the secondary IDE
connector. You may install one operating system on an IDE drive and another on
a SCSI drive and select the boot disk through Boot Sequence in 4.6 Boot Menu.

WARNING!

UltraDMA/66 IDE devices must use an 80-conductor IDE cable.

CUW IDE Connectors

NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to

PIN 1

Primary IDE Connector

Secondary IDE Connector

PIN 1

01

01

01

®

CUW

11) Floppy Disk Drive Connector (34-1 pin FLOPPY)

This connector supports the provided floppy drive ribbon cable. After connect-
ing the single end to the board, connect the two plugs on the other end to the
floppy drives. (Pin 5 is removed to prevent inserting in the wrong orienta-
tion when using ribbon cables with pin 5 plugged).

NOTE: Orient the red markings on
the floppy ribbon cable to

PIN 1

CUW Floppy Disk Drive Connector

PIN 1

01

01

01

®

CUW

«
...
32
33
34
35
36
...
»

Содержание CUW

































































































































Отзывы:

Нет отзывов

Похожие инструкции для CUW

Бренд: Panasonic Страницы: 26

Бренд: E-peas Страницы: 2

Бренд: Texas Instruments Страницы: 52

Industrial NUC-J6412

Бренд: ASROCK Страницы: 2

Бренд: ECS Страницы: 27

S1V30080 Series

Бренд: Seiko Epson Страницы: 10

Бренд: MediaQ Страницы: 25

Бренд: FAAC Страницы: 8

Бренд: Texas Instruments Страницы: 38

Бренд: Epcom Страницы: 8

Бренд: ASROCK Страницы: 64

A320M PRO-VH PLUS

Бренд: MSI Страницы: 154

Бренд: IBASE Technology Страницы: 81

Бренд: Acrosser Technology Страницы: 3

Бренд: Gigabyte Страницы: 39

Бренд: MSI Страницы: 126

Бренд: ON Semiconductor Страницы: 20

Бренд: Aaeon Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды