Asus Book Size PC System Genie Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 26

background image

Genie Book Size PC System

15

Installing the Motherboard

A FlexATX motherboard that
measures 19.05cm (7.5in) x
19.05am (7.5in) fits into the
Genie Book Size PC chassis.

1. Remove the riser card

holder by lifting it up and
unhooking it from the back
panel frame.

2. Place the motherboard into

the chassis as shown, and
making sure that the I/O
connectors fit the holes on
the I/O plate.

3. Secure the motherboard

with four screws on the
areas indicated by circles.

«
...
13
14
15
16
17
...
»

Содержание Book Size PC System Genie



























Отзывы:

Нет отзывов

Похожие инструкции для Book Size PC System Genie

Бренд: Olivetti Страницы: 254

Бренд: S&T embedded Страницы: 23

Бренд: Stage right Страницы: 12

ESPRIMO Q5 Series

Бренд: Fujitsu Страницы: 61

Бренд: Corvus systems Страницы: 19

Бренд: Shuttle Страницы: 1

Prima XPC Barebone SX48P2 Deluxe

Бренд: Shuttle Страницы: 58

Бренд: Lucent Technologies Страницы: 4

Бренд: Shuttle Страницы: 23

Бренд: AMSTRAD Страницы: 520

Genie Ultra Micro

Бренд: Viglen Страницы: 2

Бренд: 3M Страницы: 34

Бренд: Stanley Страницы: 452

Бренд: IBASE Technology Страницы: 102

Бренд: Aaeon Страницы: 73

Power System System E950

Бренд: IBM Страницы: 106

Бренд: Tandy Страницы: 171

Бренд: Keithley Страницы: 145

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды