ASTRO-PHYSICS Mach1GTO Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 31

ASTRO-PHYSICS Mach1GTO Скачать руководство пользователя страница 24

FOCUS Connector

Attach the 3.5mm phono plug connector of your JMI Motofocus or other electric focuser (optional accessories) here.

Refer to

the section regarding focus adjustment in the GTO Keypad Manual for instructions on using the keypad controller to adjust
focus.

RETICLE Connector

If you wish to use the illuminator cable for our polar alignment scope or plug-in-type guiding eyepiece with an illuminated
reticle (available from several manufacturers), insert the 3.5mm phono plug into this connector for power. Reticle brightness
can be adjusted with the hand control. Refer to the section pertaining to reticle illuminator adjustment in the GTO Keypad
manual for further information.

AUTOGUIDER Connector

This connector interfaces with the RJ-11-6 modular jack of an autoguider cable, purchased separately or as part of a CCD
Imaging Camera or Autoguider. The autoguider will be functional and ready to go as soon as you plug it in. Please refer to
the appropriate manual from the manufacturer for operation of the autoguider.

+6V Connector

This 6-volt output accepts 3.5mm phono plugs. It was designed primarily to power the Pentax 6x7 camera directly from the
mount with a cord manufactured by Pentax. In the past we have sold this as our part # CORD01. However, as of this
writing, it is not available from Pentax.

N and S Switch

Select northern (N) or southern (S) hemisphere as needed. When you slide the switch to the opposite position, the tracking
direction of the drive will reverse. The power cord must be removed and re-attached to make this work.

Drainage Holes

Two holes are drilled into the lower portion of the bottom of the control box. These holes allow excess moisture to drain from
your control box, particularly useful on dewy nights. Please do not plug these holes.

23

«
...
22
23
24
25
26
...
»

Содержание Mach1GTO
































Отзывы:

Нет отзывов