manualshive.com logo in svg

ASTRO-PHYSICS GTOCP3, Руководство пользователя

Поделиться
Скачать
ASTRO-PHYSICS GTOCP3 Скачать руководство пользователя страница 20

20 

N and S Switch 

Select northern (N) or southern (S) hemisphere as needed. When you slide the switch to the opposite position, the tracking 
direction of the drive will reverse. The power cord must be removed and re-attached to make this work. 

Removing the GTO Control Box From 1200 Mount 

The GTO control box can be removed easily from the RA axis. It is secured by two 8-32 set 
screws located at the base of the GTO Servo Control Box. Loosen the screws with one of 
the hex keys from the set included with the mount. Lift the box up from the bottom and tilt so 
that it frees from the dovetail connection.  

Some people have a permanent observatory, yet prefer to store their electronics in their 
home to keep them clean and free of cobwebs. If you do, you may wish to substitute the 8-
32 thumbscrews (included with your mount and shown in photo) for the setscrews. This will 
allow you to remove and install your GTO control box without tools.   

 

GTO KEYPAD OPERATION 

Please refer to the manual for the GTO Keypad Controller for complete instructions.  

PULSEGUIDE BY SIRIUS-IMAGING 

See 

www.pulseguide.com

 for the latest information. 

 

 

Содержание GTOCP3




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды