Associated Research 3030D Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 43

Associated Research 3030D Скачать руководство пользователя страница 36

OPTIONS

32

MODEL 3030D OPTIONS

Introduction

This

section

contains a list with descriptions of available factory installed options at the

time of this printing.

Option Label

If your instrument has been modified with options, there will be an option label on the
rear panel of the unit. The option label contains an option(s) code that may be cross-
referenced to the 3030D Options List.

The option(s) code would appear as follows:
fitted with option 02 ..............................................................

OPT: 02

fitted with option 02 and 03....................................................

OPT: 0102

3030D Options List

Code Description

01 Rear

Outputs

02 Floating

Return

Description
01

Rear Outputs

The Rear Outputs option gives the user the capability to access the High Current, Return
and Interconnect outputs from the rear panel for use in automated systems. The
configuration and descriptions are as follows.

OPTIONAL REAR PANEL CONTROLS

1

2

3

1.

CURRENT OUTPUT JACK:

For the connection of the detachable 5-foot (1.52 m)

red test lead. This jack is always used when performing a Ground Bond test.

«
...
34
35
36
37
38
...
»

Содержание 3030D












































Отзывы:

Нет отзывов