Associated Electrics SC10 4x4 Скачать руководство пользователя страница 30

Страница: 30 / 70

:: Belt, Tensioners, Spur Gear, and Covers Assembly - Bag K-KK

:: Belt, Tensioners, Spur Gear, and Covers Assembly (cont.) - Bag K-KK

Build

two!

Round

side

out

Rear Belt

Tensioner

91091

Belt

tensioner

cam

31402

4x8mm

bearing

91013

Belt

tensioner

pulley

91158

M3x4mm

bhcs

91167

Rear pulley,

20T

(no markings)

91092

Inner

slipper hub

and bushing

91090

Slipper

thrust

bearing

91090

Slipper

thrust

spacer

91090

Slipper

thrust

washer

31531

M3x6mm

bhcs

89528

M3x5.6mm

washer

91088

Rear inner

belt cover

25658

M3x6mm

shcs

91159

M2.5x5mm

shcs

91091

M2.5x5mm

washer

Install

in this

direction

on top

shaft

#1596

thread lock

#1596

thread lock

Install

inner slipper

hub in this

direction on

top shaft

The included optional

19 tooth pulley is

marked with a “U”

(underdrive).

To adjust the belt tensioner, you

need to remove the #91159

shcs and the #91091 washer.

Loosen the #31531, adjust

the belt tensioner, and reinstall

the #91091 washer and the

#91159 shcs.

See notes!

Содержание SC10 4x4







































































Результаты поиска

Содержание SC10 4x4

Отзывы:

Associated Electrics SC10 4x4, Руководство пользователя, Страница: 30 / 70

Результаты поиска

Содержание SC10 4x4

Отзывы: