Associated Electrics FS-GT15 Скачать руководство пользователя страница 1

 

 

  FS-GT15 2.4GHz 3IN1

 

ELECTRONIC SYSTEM 

USER’S GUIDE V1.0 

DESCRIPTION 

FS-GT15 is a 3 in 1 multifunction 2.4GHz electronic system build for RC cars. It 

has built in servo and ESC inside the receiver all these features just in one small piece. 

SPECIFICATIONS 

 

Transmitter Model

FS-GT15 Tx 

 

Transmitter Frequency

2.4G 

GFSK

 

 

Remote control distance: >40m 

 

Power Supply

4 Cell AA Batteries 

 

Configuration mode: button  

 

 

Receiver Model

FS-GT15 Rx 

 

Voltage Range

1S Lipo 

 

Receiver frequency: 2.4G (GFSK) 

 

Supported motor: 180 brush motor, 180 carbon brush motor or 0716 hollow cup 

motor 

 

Supported servo: 5g or 9g 5-wire servo. 

FEATURES DESCRIPTIONS 

 

2 channel transmitters, set ST TRIM and TH DR. 

 

Integration of Receiver, ESC and servo, high integration, install conveniently. 

 

Throttle neutral point adaptation without the TRIM setting of TH. 

 

Low voltage cut-off protection for battery / Throttle signal loss protection. 

Declarations and Warnings

       FS-GT15 Rx is a highly-integrated multifunction ESC. It has built-in functions of 

ESC, servo and 2-channel receiver. It must work with right motor and servo in order 

to get FS-GT15 Rx work properly, otherwise the FS-GT15 RX will be destroyed. 

Don’t block the motor for a long time, which will damage the ESC. 
Don’t block the servo for a long time, which will damage the servo driver. 

Содержание FS-GT15







Отзывы: