Associated Electrics 4015 RC12 L3 Скачать руководство пользователя страница 8

TEAM ASSOCIATED ONLINE!

18

REAR AXLE HEIGHT
ADJUSTERS

Your car comes with four sets of rear axle height
adjuster inserts. These inserts allow you to raise
or lower the height of the back of the car without
changing tire diameters. Even though there are only
four offsets, three can be rotated 180° for a total of
seven different axle heights as shown.

The #4-up position allows you to use the maximum diameter tire and the #4-down position requires you to
use the minimum tire diameter. This adjustment allows you to get more useful life from a set of tires by
adjusting axle height as tire diameter decreases. You can also adjust the overall height of your car for high
or low traction conditions.

INCREASING STEERING

To increase steering, replace  the stock #8421 steering blocks with the optional
#8441 inline steering blocks and #8443 axles. This will make the car steer very
aggressive. Note: The inline axles use #6902 bearings.

 SETUP SHEET

The next page shows  Team Associated’s

setup sheet for your car. Copy this form and keep a
record of the settings you used for a particular track.
This record of your settings will make it easier to
set up your car the next time you race at that track,
as well as compare differences between tuning ad-
justments. This is a feature that our Team drivers
take full advantage of.

3585 Cadillac Ave.
Costa Mesa, CA  92626
(714) 850-9342
fax (714) 850-1744
http://www.rc10.com

FRONT RIDE
HEIGHT

To obtain your desired ride height,
you can place a thick #3323
aluminum spacer under the lower
suspension arm. To raise the car,
take away spacers, and to lower
the car, add spacers.

SAVE THIS  BOOKLET!

More than an instruction manual,

its also a handy pictorial supplement
to Team Associated’s RC12L3 cata-
log.

Refer to this manual for part num-

bers and description when ordering
parts or to explain problems for cus-
tomer service calls.

TEAM ASSOCIATED ONLINE!

Get online help, tips, and new products
for your kit through Team Associated’s
web site!

Tech Help, where answers to racers’
questions are posted for all to learn from.

Racer Spotlight, where other racers
proudly show off their favorite kit.

Setup Sheets, where racers go to find
blank and standard setups to download for
their kit.

New Products, where you learn of new kits
and parts before they are announced
anywhere else!

Team Associated Insiders Newsletter.
Sign up for it on the Home Page if you want
news delivered right to your e-mail box!

Question of the Week. Join in and give
your opinion of the topic of the week, and
learn form other racers.

Hobby Shop and Track listings. Shops
that carry Associated parts and where you
can race your kit.

R/C Kits and Parts. Online catalogs
updated with new parts as soon as they
come out.

Feedback Form. Tell us what’s on your
mind with this exhaustive survey.

Help Form. Our expert staff answers your
toughest questions about Associated,
Reedy, and LRP products.

Free Stuff. Get your Associated kit com-
puter wallpaper and screensavers here!

http://www.teamassociated.com

Содержание 4015 RC12 L3











Отзывы: