CONCRETE HAMMER DRILL
SAFETY SHEET
(Hilti TE60-ATC/AVR)
SETTING THE POWER LEVEL
1. Press the power reduction button. The product runs at reduced power
(50 %). The reduced-power LED lights.
2. Press the power reduction button again. The product runs at full
power. The reduced-power LED goes out.
DRILLING WITH HAMMERING ACTION
1. Set the function selector switch to this symbol:
2. Set the desired power level.
3. Press the drill bit against the work surface.
4. Press the control switch. The product starts.
CHISELING
1. Set the function selector switch to this symbol:
SWITCH SUSTAINED OPERATION ON & OFF
When chiseling, the control switch can be locked in the “on” position.
1. Push the lockbutton for continuous operation forward.
2. Press the control switch fully. The product then runs in sustained
operating mode.
3. Push the lockbutton for continuous operation back. The product
switches off.
MAIN COMPONENTS
English
9
3 Description
3.1 Overview of the product
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
10 English
@
Chuck
;
Depth gauge
=
Function selector switch
%
Control switch
&
Supply cord
(
Side handle
)
Lockbutton for continuous
operation
+
Service indicator
§
Reduced-power indicator
/
Power reduction button (50%
power)
3.2 Version with detachable supply cord
@
Lockbutton
;
Connector on electric tool
=
Supply cord with keyed, re-
leasable plug connector
3.3 Intended use
The product described is an electrically-powered combihammer with pneu-
matic hammering mechanism. It is designed for drilling in concrete, masonry,
wood and metal. The product can also be used for light to medium-duty
chiseling on masonry and surface finishing work on concrete.
Under certain conditions, the product may also be suitable for stirring /
mixing.
▶
The power tool may be operated only when connected to a power supply
providing a voltage and frequency in compliance with the information
given on its type plate.
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
English 15
3. Tighten the side handle clamping band by turning the handle grip.
5.1.3 Setting the power level (optional)
TE 60-ATC/AVR
Note
After the supply cord is connected to the AC supply, the product is
always set by default to full power.
1. Press the power reduction button. The product runs at reduced power
(50 %).
◁
The reduced-power LED lights.
2. Press the power reduction button again. The product runs at full power.
◁
The reduced-power LED goes out.
5.1.4 Fitting the accessory tool
1. Apply a little grease to the connection end of the accessory tool.
◁
Use only the recommended grease supplied by
Hilti
. Using the wrong
grease can result in damage to the tool.
2. Push the accessory tool into the chuck as far as it will go (until it engages).
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
English 17
5.2.1 Drilling with hammering action (hammer drilling)
1. Set the function selector switch to this symbol: .
2. Set the desired power level.
3. Press the drill bit against the work surface.
4. Press the control switch.
◁
The product starts.
5.2.2 Drilling without hammering
Note
Drilling without hammering action is possible when accessory tools with
a special connection end are used. Accessory tools of this kind are
available from
Hilti
. Alternatively, when the keyless quick-release chuck
is fitted, smooth-shank drill bits for wood or steel, for example, can be
used to drill without hammering.
▶
Set the function selector switch to this symbol: .
5.2.3 Mixing
Note
Use the mixing paddle only with the quick-release chuck.
Use the mixing paddle only when the reduced power (50 %) setting is
active.
1. Insert the quick-release chuck in the power tool’s chuck.
2. Fit the mixing paddle into the quick-release chuck.
3. Set the function selector switch to this symbol: .
4. Press the power reduction (50 %) button.
◁
The product is ready for use.
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
English 17
5.2.1 Drilling with hammering action (hammer drilling)
1. Set the function selector switch to this symbol: .
2. Set the desired power level.
3. Press the drill bit against the work surface.
4. Press the control switch.
◁
The product starts.
5.2.2 Drilling without hammering
Note
Drilling without hammering action is possible when accessory tools with
a special connection end are used. Accessory tools of this kind are
available from
Hilti
. Alternatively, when the keyless quick-release chuck
is fitted, smooth-shank drill bits for wood or steel, for example, can be
used to drill without hammering.
▶
Set the function selector switch to this symbol: .
5.2.3 Mixing
Note
Use the mixing paddle only with the quick-release chuck.
Use the mixing paddle only when the reduced power (50 %) setting is
active.
1. Insert the quick-release chuck in the power tool’s chuck.
2. Fit the mixing paddle into the quick-release chuck.
3. Set the function selector switch to this symbol: .
4. Press the power reduction (50 %) button.
◁
The product is ready for use.
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
18 English
5.3 Chisel positioning
CAUTION
Risk of injury!
Loss of control over the chisel direction.
▶
Do not operate the tool when the selector switch is set to “Chisel
positioning”. Turn the function selector switch until it engages in the
“Chiseling” position.
Note
The chisel can be adjusted to 24 different positions (in 15° increments).
This ensures that flat chisels and shaped chisels can always be set to
the optimum working position.
1. Set the function selector switch to this symbol: .
2. Rotate the chisel to the desired position.
3. Set the function selector switch to this symbol: until it engages.
◁
The product is ready for use.
5.3.1 Chiseling
▶
Set the function selector switch to this symbol: .
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
English 17
5.2.1 Drilling with hammering action (hammer drilling)
1. Set the function selector switch to this symbol: .
2. Set the desired power level.
3. Press the drill bit against the work surface.
4. Press the control switch.
◁
The product starts.
5.2.2 Drilling without hammering
Note
Drilling without hammering action is possible when accessory tools with
a special connection end are used. Accessory tools of this kind are
available from
Hilti
. Alternatively, when the keyless quick-release chuck
is fitted, smooth-shank drill bits for wood or steel, for example, can be
used to drill without hammering.
▶
Set the function selector switch to this symbol: .
5.2.3 Mixing
Note
Use the mixing paddle only with the quick-release chuck.
Use the mixing paddle only when the reduced power (50 %) setting is
active.
1. Insert the quick-release chuck in the power tool’s chuck.
2. Fit the mixing paddle into the quick-release chuck.
3. Set the function selector switch to this symbol: .
4. Press the power reduction (50 %) button.
◁
The product is ready for use.
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
English 19
5.3.2 Switch sustained operation on and off
Note
When chiseling, the control switch can be locked in the “on” position.
1. Push the lockbutton for continuous operation forward.
2. Press the control switch fully.
◁
The product then runs in sustained operating mode.
3. Push the lockbutton for continuous operation back.
◁
The product switches off.
6 Care and maintenance
WARNING
Danger of electric shock!
Carrying out care and maintenance while the
supply cord is connected to the power outlet presents a risk of serious
injuries including burns.
▶
Always unplug the supply cord before carrying out all care and
maintenance tasks.
Care
• Carefully remove any dirt that may be adhering to parts.
• Clean the air vents carefully with a dry brush.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning
agents containing silicone as these may attack the plastic parts.
Maintenance
WARNING
Danger of electric shock!
Improper repairs to electrical components
may lead to serious injuries including burns.
▶
Repairs to the electrical section of the tool or appliance may be
carried out only by trained electrical specialists.
Printed: 28.06.2017 | Doc-Nr: PUB / 5277962 / 000 / 01
