RF4510: EXTERNAL ANTENNA
Installation Directions
1. Prepare door jamb for hybrid electric strike per the appropriate
template detail on page 5. Be sure to allow enough room
behind the strike in the cutout to avoid pinching any wires.
2. Drill a 1” diameter hole for the reader/antenna per the
appropriate template detail on page 5. The reader/antenna may
be positioned as desired, within the limits of the 24” cable. (If
necessary, drill a channel from the reader/antenna to the hybrid
electric strike to accomodate the 24” cable.)
3. Drill a 3/8” hole for the door position switch per the appropriate
template detail on page 5. The door position switch may be
positioned as desired, within limits of its 10” connector. If
necessary, drill a channel from the door position switch to the
hybrid electric strike to accomodate the 10“ cable. . Align and drill
a matching 3/8” hole in the door and install the press-fit magnet
so that it will trigger the door position switch.
4. If applicable (e.g. aluminum frames), install mounting tabs (sold
separately as P/N 152) using #10-32 screws.
9. Connect the 24” cable to the reader/antenna (check labels to
insure that you connect the correct end). Then, install the
reader/antenna in the frame, using the #6-32 screws provided.
Snap on the reader/antenna cover and pull the 24”cable through
to the hybrid electric strike.
10. Plug the loose end of the 24” cable into the connector on the
side of the hybrid electric strike.
Prepare Hybrid Electric Strike & Frame
11. Install the trim enhancer on the hybrid electric strike
(see page 4) if needed, to cover any extra space.
12. Install the hybrid electric strike unit in jamb cutout, using
#12-24 screws provided.
13. If needed, see page 4 to make horizontal adjustments in
frame .
14. If applicable, tighten the #10-32 screws holding the
mounting tabs.
Finish Installing
15. When power is supplied to the hybrid electric strike, the LED
will flash green three times, while the beeper simultaneously
beeps. The LED will then turn red. This sequence indicates that the
micro-controller is operating properly.
16. Present a Proximity ID card to the reader/antenna. The LED will
turn green, while the beeper beeps once. This indicates that the
card was read successfully.
17. Simultaneously, the keeper will click open. This indicates that
communication between the host and the hybrid electric strike is
operational.
18. For further testing of communication with the host, consult the
manual for the control panel or the site’s system administrator.
Testing and Operation
Connect Components and Wiring
Wire Gauge Diagram
Max. One-way Distance Voltage Drop/100’ Recommended AWG
800’
500’
300’
200’
120’
100’ or less
12VDC @ 240 mA
0.15
0.24
0.38
0.61
0.97
1.53
12 Gauge
14 Gauge
16 Gauge
18 Gauge
20 Gauge
22 Gauge
3
6. Verify that the wires running from the host control panel are of
adequate gauge (see Wire Gauge Diagram below). Connect the
wire leads of the three pigtails provided to the host control panel
wiring based on the wiring diagram on page 2 and the appropriate
termination at the host control panel.
7. Mount the door position switch (DPS) into the frame. Route the
10” cable back to the electric strike and connect it to the 2 pin
connector coming out of the hybrid electric strike. It does not
matter which 2 pin connector is used. The LBM & DPS are wired in
series--a ‘closed’ electrical circuit depicts a closed door and extended
latchbolt into the hybrid electric strike.
8. Attach the 8, 4 and 2 pin connectors at the hybrid electric strike
to the equivalent pigtail connectors routed from the host control
panel. Dielectric grease should be applied to the pigtail electrical
terminals if used in a humid environment
CAUTION! Before connecting any device at the installation site, verify that there is 12VDC input voltage using a multimeter.
Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage outside the electrical
specifications outlined on page 1 may cause severe damage to the unit and will void the warranty. This product contains
electrostatic sensitive components. We recommend proper grounding techniques be observed during installation.
5. The appropriate Deadlatch Tab for the lockset being used with
the hybrid electric (see page 4) should also be installed at this time
