background image

6

MP6600 Series Multi-Point Lock

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

FM556  08/20

Copyright © 2020, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or 
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • [email protected]

5 Installation, 

continued

e

Install Cylinder

Cylinder

Cylinder 
Clamp 
Screw

Figure 9 

 

Incorrect

Key and cylinder must be rotated as shown.

Correct

Figure 10 

  

1.  Thread cylinder into lock until flush with 

escutcheon surface. (Figure 9)

•  Pull key slightly out of cylinder to help thread 

into lock body.

2.  Tighten cylinder clamp screw with #1 Phillips 

screwdriver.

•  Check operation and adjust cylinder if 

necessary.

Notes:

• 

SARGENT logo must be horizontal and on 

top. (Figure 10)

• 

 If double cylinder function is used, repeat 
steps 1 and 2 for second cylinder.

• 

 Removable Core or Interchangeable Core 
cylinders require a control key (key stamped 
with C) to remove and install the core.  This is 
not provided standard; it must be requested 
separately.  If requesting 1-bitted control key, 
specify 113511 cut.

f

Install Outside Front

1.  Tighten the two (2) lock screws completely. (Figure 11)

2.  Attach outside front with two (2) flat head screws #8-32 x 1/4.

Figure 11 

 

Lock 
screw

Outside 
front

Lock screw

#8-32 x 
1/4" screws

g

Perform Function Check

DO NOT FORCE if resistance is encountered during functional 
check. Refer back to Rehanding Indicator (if required) section 
to ensure correct handing. Rehand if necessary.

1.  Insert key into cylinder (if present) and rotate: 

•  Ensure there is no friction against lock case or 

any other obstructions.

2.  Check key retracts latch:

•  Key should rotate freely.

3.  Throw deadbolt (if present): 

•  Check key retracts both deadbolt and latch.

4. Test levers:

•  Confirm latch and deadbolt (if installed) retract.

5.  Verify indicator displays correct status when locked 

and unlocked

Содержание Corbin Russwin MP6600 Series









Отзывы: