background image

59

3.6  Boot Screen

In this section, it will display the available devices on your system for you to config-
ure the boot settings and the boot priority. 

Fast Boot 

Fast  Boot  minimizes  your  computer’s  boot  time. There  are  three  con-
figuration options: [Disabled], [Fast] and [Ultra Fast]. The default value is 
[Disabled]. Please refer to below descriptions for the details of these three 
options: 
[Disabled] - Disable Fast Boot.
[Fast] - The only restriction is you may not boot by using an USB flash 
drive.
[Ultra Fast] - There are a few restrictions.
  1. Only supports Windows

®

 8 UEFI operating system. 

  2. You will not be able to enter BIOS Setup (Clear CMOS or run utility  
      in Widows

®

 to enter BIOS Setup). 

  3. If you are using an external graphics card, the VBIOS must support  
      UEFI GOP in order to boot.

Boot From Onboard LAN
 

Use this item to enable or disable the Boot From Onboard LAN feature.

Setup Prompt Timeout
 

This  shows  the  number  of  seconds  to  wait  for  setup  activation  key. 
65535(0xFFFF) means indefi nite waiting.

Bootup Num-Lock

  If  this  item  is  set  to  [On],  it  will  automatically  activate  the  Numeric  Lock 

function after boot-up.

Содержание 970 Extreme3 R2.0







































































Отзывы: