background image

2

E   N   G   L   I   S   H

C E X - 7 0

1. GENERAL

1.1 

 

INTRODUCTION

This manual was prepared with the aim of making the installation and management of your system as simple as 

possible.

By reading and applying the suggestions of this manual, you can achieve the best performance of the purchased 

product.

We would like to thank you for choosing to purchase one of our products.

Read this file carefully before performing any operation on the unit.

The unit must not be installed, nor must any operation be performed on it, without firstly reading and understanding 

the entirety of this manual. In particular it is necessary to adopt all of the precautions listed in the manual.

The documentation provided with the unit must be delivered to the system manager for safe keeping (at least 10 

years) for future assistance, maintenance and repairs.

Unit installation must take into account the strictly technical needs for good operation, as well as any local 

legislation in force and specific requirements.

Make sure that when the unit is delivered there are no evident signs of damage caused by transport. If there is, 

state this on the delivery note.

This manual reflects the state of the technical standards at the time of sale and cannot be considered inadequate 

if updated at a later date based on new experiences. The Manufacturer reserves the right to update production and 

the manuals without being required to update previous ones, except in exceptional cases.

Contact the Manufacturer’s Sales Office to receive further information or updates on/to the technical documentation 

and for any suggestions for improvement to this manual. All suggestions shall be strictly vetted.

1.2  FUNDAMENTAL SAFETY RULES

This instruction is an integral part of the manual of the device that the KIT is installed on. Refer to said 

manual for the GENERAL WARNINGS and for the FUNDAMENTAL SAFETY RULES. Installation must be 

carried out by qualified personnel equipped with the necessary PERSONAL PROTECTIVE EQUIPMENT.

compliance with local regulations.

Содержание CEX-70













Отзывы: