background image

Neo Mini                                  Aerospace Speciality Products                                        Page 3

the rings or remove a layer or two of the paper wrap from the inside of the centering ring (use your 
knife to loosen an edge of the paper and carefully pull it out). 

Take the engine tube, and with your 

hobby knife make a small horizontal slit about 1/8" wide and 3/16" from one end of the tube. Make a 
pencil mark 5/8" from the other end of the tube.

Slide First Centering 

Ring Just Over Hook

Apply Glue Around 

OUTSIDE of Tube 

Here

Engine 

Hook

5/8" Mark 

From End 

of Tube

Make Slit Here

Top 

End 

of Tube

       

First Centering 

Ring

Engine 

Hook

5/8" Mark 

From End 

of Tube

Second Centering 

Ring

Make Slit Here

Engine 

Block

Kevlar

® 

Cord

Kevlar

® 

Cord

 

 

 

Figure A 

 

 

 

 

 

Figure B

Slip one of the “hook” ends of the metal engine hook into the slit (you can hold the hook in place 
with a small piece of tape if you need to) - be sure the hook is straight along and parallel to the 
tube. Slip one of the centering rings over the top end of the tube (the end closest to the slit) and 
down just over the hook. Apply a thin layer of glue to the outside of the engine tube just above the 
5/8" mark (see Figure A) and slide the centering ring down until it is in the proper location (see 
Figure B, this is the location of the “First Centering Ring”) - be sure to check the alignment of the 
engine hook.
Take the Kevlar

®

 and tie one end firmly around the middle of the engine tube and hook as shown in 

Figure B. Slip the second centering ring over the loose end of the Kevlar

®

 and down over the end 

of the tube. Apply glue around the outside of the tube and slide the second ring in place as shown. 
Apply a small amount of glue inside the top of the tube above the end of the metal hook and push 
the engine block into place. Allow the glue to dry thoroughly. 

 2) Locate the white elastic shock cord. Take the loose end of the Kevlar® and one end of the 

elastic and hold the ends evenly. Tie a simple overhand knot about 1/2" to 1" from the ends and 
tighten down the knot firmly so the two pieces of material are held tightly together. If needed, trim 
the loose ends to about 1/4" to 1/2" long. See these steps shown left to right in Figure C.

          

Make marks at 

!

ends of arrows

!

on guide

Align marks at 

!

ends of guide

Body

!

Tube

 

 

   Figure C   

 

 

 

 

Figure D

 

3) Locate the white body tube. Very lightly sand the outside the of the tube with medium or fine 

sandpaper until the surface just loses its shine. This will allow the glue to penetrate the paper of the 
tube and the fins to stick to the tube better. Cut out the Tube Marking Guide from the last page of 
these instructionst. Wrap the guide around the body tube - line up the marks on each end to align 

Содержание Neo Mini











Отзывы: