manualshive.com logo in svg

ASM 248772 A series, Руководство по эксплуатации

Поделиться
Скачать
ASM 248772 A series Скачать руководство пользователя страница 2

2

310749

Specifications

This equipment is not intended for applications in places such as cabinet shops or other “factory”, fixed 
locations or for repetitive applications.  If you intend to use this equipment in this type of application, you must com-
ply with NFPA 33 and OSHA requirements which have similar expectations.

The following are general warnings related to the setup, use, grounding, maintenance, and repair of this equipment.
Additional, more specific warnings may be found throughout the body of this manual where applicable.  Symbols
appearing in the body of the manual refer to these general warnings.  When these symbols appear throughout the
manual, refer back to these pages for a description of the specific hazard.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode.  To help
prevent fire and explosion:

D

 Use equipment only in well ventilated area.

D

Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and
plastic drop clothes (potential static arc).

D

Sprayer generates sparks.  When flammable liquid is used in or near sprayer or for flushing or
cleaning, keep sprayer at least 20 ft (6 m) away from explosive vapors.

D

Keep work area free of debris, including solvent, rags and gasoline.

D

Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

D

Ground equipment and conductive objects in work area.  Read Grounding instructions.

D

If there is static sparking or you feel a shock, stop operating immediately.  Do not use equip-
ment until you identify and correct the problem.

D

Keep a fire extinguisher in the work area.

ELECTRIC SHOCK HAZARD

Improper grounding, setup, or usage of the system can cause electric shock.

D

Turn off and disconnect power cord before servicing equipment.

D

Use only grounded electrical outlets

D

Use only 3–wire extension cords.

D

Ensure ground prongs are intact on sprayer and extension cords.

D

Do not expose to rain.  Store indoors.

SKIN INJECTION HAZARD

High pressure fluid from gun, hose leaks, or ruptured components will pierce skin.  This may look like
just a cut, but it is a serious injury that can result in amputation.  

Get immediate surgical treatment.

D

Do not point gun at anyone or any part of the body.

D

Do not put your hand over the spray tip.

D

Do not stop or deflect leaks with your hand, body, glove, or rag.

D

Engage trigger lock when not spraying.

D

Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking or servicing equipment.

Содержание 248772 A series



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды