background image

6 - T9 PRO

ASL MACHINES USA 2018 ©

Never try to replace parts or repair equipment 

with machine running.

Turn the gas off at the tank to kill the engine.

Remove the LPG tank and store it in an 

approved area when not in use. a “NO 

SMOKING” sign should be permanently 

displayed at the storage area.

Always vent an over-full bottle using the 

tank’s bleed valve, out of doors away from 

all closed places and away from any  fire or 

flame producing device. Vent until the white 

vapor turns clear.

This machine is intended for use with vapor 

withdraw propane cylinders only. NEVER use 

a liquid withdraw propane cylinder with this 

equipment. DO NOT over fill the cylinder. if 

the regulator or regulator connection freezes, 

stop the machine and take the cylinder 

outdoors. inspect cylinder and purge the 

cylinder using the bleeder valve if necessary.

Keep all objects clear of the exhaust system 

during and after operation.

Do not leave this machine unattended while 

the engine is running.

Do not operate equipment in one location 

for more than a few seconds. damage to  oor 

surface can occur.

Always store equipment away from possible 

damage by falling objects in warehouse-type 

areas. always store LPG tanks outside in a 

secure, well-ventilated area.

The mufler and engine become hot enough 

during operation to cause severe burns. 

these parts remain hot for a long time after 

the machine has been shut off. do not touch 

WARNING!

these parts until they have cooled.

Safety goggles, safety shoes and safety 

clothing are recommended while operating 

the machine.

Continuous exposure to high noise levels can 

cause hearing loss. Hearing protection must 

be worn while the machine is in operation. 

the operational weighted sound level of this 

machine is less than 89dB(a). all noise area 

precautions must be followed.

Prolonged exposure to machine vibration may 

cause tingling or numbness in the  ngers and 

hands. Use of gloves and limits to operator 

vibration exposure are recommended to 

prevent such symptoms. the operational 

hand/arm vibration level of this machine is 

less than 2.5m/s 2.

When LPG tank is attached to the machine 

and not running, the operator should not 

leave the machine unattended except for 

short periods of time such as rest stops, 

washroom or meal stops.

The operator must completely understand 

all instructions, warning and operating 

procedures before using this machine.

This machine must be maintained in 

accordance with this manual’s recommended 

maintenance instructions and the engine 

manufacturer’s recommended maintenance 

procedures. failure to do so may cause 

damage to the machine, equipment, furniture, 

buildings or personal injury. a maintenance 

record should be kept indicating date of 

service, hours on engine, and work done.

Содержание T9 PRO





























Отзывы: