Asko D5526XLFI, Руководство по эксплуатации, Страница: 8 / 20

Hyg
Hygiene wash
This program is recommended for baby bottles and cutting
boards when additional sanitation is required. The temperature
is high in the main and final rinse.
Delicate wash
If the dishes are only lightly soiled, you can select Delicate wash.
This program is intended for glasses and porcelain that have just
been used and as such do not require such a powerful program.
This program can be used for fragile dishes. Select Short dry to
be extremely cautious. See also the section Fragile dishes in
Chapter Loading the dishwasher.
Eco wash
This program is most effective in terms of combined energy and
water consumption.
Rinse & Hold
Use to rinse dishes while you wait for the dishwasher to become
fully loaded.
Selecting Options
To select an option, press one of the option buttons. The field
under the button lights when the option is activated. The available
options depend on the selected program. Once you have started
the program, the options you selected are saved for the next time
you use the same program.
High temperature
Activate this option for improved dishwashing results. The ma-
chine then uses a higher temperature for the main wash.
If you want to use the lower temperature, press again so that the
field under the button turns off.
You can vary the temperature as shown below:
150 °F (65 °C) / 160 °F (70 °C) Sanitation wash:
133 °F (56 °C) / 150 °F (65 °C) Normal wash:
140 °F (60 °C)/150 °F (65 °C) Heavy wash:
85 °F (30 °C) / 140 °F (60 °C) Quick wash:
105 °F (40 °C) / 120 °F (50 °C) Delicate wash:
130 °F (55 °C) / 140 °F (60 °C) Eco wash:
Long dry
Activate Long dry to increase final rinse temperature and dry time
to improve drying results. This causes a slight increase in energy
consumption. This option can be used with all programs except
Rinse & Hold.
If you want a program with Short dry, press again so that the field
under the button turns off.
Start the dishwasher
Press and hold Start/Stop until the display shows (the door
open symbol). This indicates that the dishwasher is ready to start.
Close the door properly, otherwise the dishwasher will not start.
NOTE!
If the machine does not start within 2 minutes of the last button
press, the display returns to showing the last program run.
Time remaining
Once you have selected a program and options, the display indi-
cates how long the program took the last time it was used. The
remaining time is updated after the water for the final rinse has
been heated.
This may differ somewhat from time to time depending on the
temperature of the water supply, the amount of dishes, the ambi-
ent temperature, and other factors.
NOTE!
During the first run of each program, the remaining time dis-
played can be slightly misleading, as the dishwasher is estimat-
ing the time. When you run the program a second time, the
dishwasher will calculate the remaining time based on the
previous duration of the program.
Stopping or changing a program
If you want to change programs after starting the dishwasher,
open the door then press and hold Start/Stop for three seconds.
Add more detergent if the lid of the detergent dispenser has
opened. Then choose a new program, press Start/Stop, and close
the door.
Do you want to add more dishes?
Open the door. The dishwasher stops automatically. Add the
dishes, close the door, and the dishwasher resumes the program.
If the dishwasher is turned off using
the On/Left-on mode button or due
to a power failure
If the program was not finished, the interrupted program resumes
when power is restored.
NOTE!
During drying, the program is interrupted if the power is cut or
the door is open for more than 2 minutes.
Once the program has finished
Once the program has finished and the door is opened, "End"
appears on the display.
At the end of the program, one short signal will sound. Chapter
Settings describes how to change this function.
Once the cycle is complete, the dishwasher uses standby power
only.
8