Page 8
OPTIONS,
OPTIONS,
OPTIONS,
OPTIONS,
OPTIONS,
CONTINUED
CONTINUED
CONTINUED
CONTINUED
CONTINUED
Drying
This lets you select how long the turbo fan runs after
the final rinse. You have three options: Short, Normal,
or Extra drying. (
Note
: This option is not available with
the Auto wash, Rinse and Hold, and Rinse and Dry
programs.) To set the drying time, press Menu until
“Drying” displays, then press Set until your preference
displays.
Express
This option reduces the wash time and lowers the wash
temperature by 20° F. (
Note
: This option is not available
with the Quick Wash and Rinse and Hold/Dry
Programs.) Press Menu until Express displays, then
press Set once to select On or twice to select Off. Press
Menu to confirm your selection.
Cool Touch
This option lets you set a cool-down cycle after the drying
program. Press Menu until Cool Touch displays, then
press Set once to select On or twice to select Off. Press
Menu to confirm your selection.
ST
ST
ST
ST
STAR
AR
AR
AR
ART/ST
T/ST
T/ST
T/ST
T/STOP BUTT
OP BUTT
OP BUTT
OP BUTT
OP BUTTON
ON
ON
ON
ON
Once you have selected the wash program and options,
press this button to start the dishwasher. (Make sure
the door is securely closed.)
F
FF
FFA
A
A
A
AUL
UL
UL
UL
ULT CODES
T CODES
T CODES
T CODES
T CODES
In the event that the machine should fail during a
program, the display window will show a fault code. The
table below defines these codes and gives possible
causes and solutions. See also “Troubleshooting” on
page 13.
Display
Type of Fault and Recommended Action
Overfilling
Too much water has entered the dishwasher. Call a service technician.
Water Inlet Fault
Water inlet fault. Make sure the water supply is open.
Inlet Valve Leakage
Valve leakage. Shut off the water supply and contact a service technician.
Drainage
The drain is blocked. See “Troubleshooting” on page 13.
Blocked Filter
The filter is clogged. See “Cleaning the Filters” on page 10.
If you have corrected the fault, turn the main power off
then back on to remove the fault indication. If it still
displays, try again to correct the problem or call a service
technician.
PROGRAM TIMES
PROGRAM TIMES
PROGRAM TIMES
PROGRAM TIMES
PROGRAM TIMES
The program times may not always be the same
because of variations in the household hot water
temperature. The dishwasher heats the water to the
proper temperature for the program selected; so if the
temperature of the water entering the dishwasher is too
low, the dishwasher will run longer because it takes
longer to heat the water. Raising your water heater
setting could help to shorten the cycle times.
INTERR
INTERR
INTERR
INTERR
INTERRUPTING
UPTING
UPTING
UPTING
UPTING A PR
A PR
A PR
A PR
A PROGRAM
OGRAM
OGRAM
OGRAM
OGRAM
TO ADD AN ITEM
TO ADD AN ITEM
TO ADD AN ITEM
TO ADD AN ITEM
TO ADD AN ITEM
If you want to interrupt a program to add an item, open
the door slightly until the spray arms stop turning. You
can then open the door fully and place the item into the
dishwasher. Close the door securely. The program will
continue from where it was interrupted.
WARNING!
Be extremely careful when opening the
door during a program. The water is hot and you
could get scalded.
CHANGING OR ST
CHANGING OR ST
CHANGING OR ST
CHANGING OR ST
CHANGING OR STOPPING
OPPING
OPPING
OPPING
OPPING A
A
A
A
A
PR
PR
PR
PR
PROGRAM
OGRAM
OGRAM
OGRAM
OGRAM
If you decide to change the program after you have started
the machine, press the Start/
Stop
button for three
seconds. You will have to select the program and options
again when you are ready to restart the program. (
Note:
If the program has already gone through the wash cycle,
you will have to add detergent.)
