manualshive.com logo in svg

Ask aks-S4, Руководство по эксплуатации

Поделиться
Скачать
Ask aks-S4 Скачать руководство пользователя страница 23

aks-S4

Page 23 

z4200064_

GA_Bett_S4_151015_EN

Accessories / combination

10 

Only original aks accessory parts must be used as accessories because these are tested by ourselves 

and thus guarantee faultless and safe functioning. Combinations which have not been approved by 

aks can cause hazards.

Accessories:

Foam mattress RG 35 kg/m³, 90x200x12 cm, 8 kg   

 

Order No.: 77050

• 

Side grill height extender 

• 

(mandatory when using large‑cell mattresses) 

 

 

Order No.: 39047

Side grill padding (one side)   

 

 

 

 

Order No.: 77551

• 

Uplifter with grab handle 

 

 

 

 

 

Order No.: 77020

• 

Other accessories on request.

Combination:
Other aks products can also be used with the homecare bed. For example, these include our aks 

antidecubitus systems or our aks patient hoists.

Only use mattresses whose dimensions correspond to the dimensions of the lying area (also when 

using the bed extension). If there is not a distance of at least 220 mm between the mattress surface 

and the top edge of the side grill, you must use a side grill height extender.

Non-original side grills can cause hazards.

Содержание aks-S4





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды