Ashley 1440E Скачать руководство пользователя страница 4

-

4

-

Safety

•  WARNING: Do not operate with fuel loading or ash removal doors open.

•  Do not connect this unit to a chimney flue serving another appliance.

•  WARNING DANGER: Risk of fire or explosion. Do not burn garbage, gasoline, naphtha, motor oil, or other 

inappropriate materials. Do not use chemicals or fluids to start the fire.

•  WARNING: Risk of fire. Do not operate with flue draft exceeding .060” water column/14.93 Pascals. Do not 

operate with fuel loading and ash removal doors open. Do not store fuel or other combustible materials 

within marked installation clearances. Inspect and clean flues and chimney regularly.

•  CAUTION: Hot surfaces. Keep children away. Do not touch during operation.

•  The heat exchanger, flue pipe, and chimney must be cleaned regularly to remove accumulated creosote 

and ash. Ensure that the heat exchanger, flue pipe, and chimney are cleaned at the end of the heating 

season to minimize corrosion during the summer months. The appliance, flue pipe, and chimney must be 

kept in good condition. These instructions also apply to a draft inducer if used. To prevent flame or smoke 

spillage, the slide baffle must be pulled out and the fuel loading door left cracked for 10 seconds prior to 

opening door fully. Load fuel carefully or damage may result.

•  Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

•  Do not use chemicals or fluids to ignite the fire.

•  Do not leave the furnace unattended when the door is slightly opened.

•  Do not burn garbage, flammable fluid such as gasoline, naphtha or motor oil.

•   Always close the door after the ignition.

•  Consult your municipal building department or fire officials about permits, restrictions and installations 

requirements in your area.

•  INSPECT FLUE PIPES, FLUE PIPE JOINTS, AND FLUE PIPE SEALS REGULARLY TO ENSURE THAT SMOKE AND FLUE 

GASES ARE NOT DRAWN INTO, AND CIRCULATED BY, THE AIR-CIRCULATION SYSTEM.

•  CAUTION: CLEAN OUT OF THE HEAT EXCHANGER, FLUE PIPE CHIMNEY, AND DRAFT INDUCER, IF USED, IS 

ESPECIALLY IMPORTANT AT THE END OF THE HEATING SEASON TO MINIMIZE CORROSION DURING THE SUMMER 

MONTHS, CAUSED BY ACCUMULATED ASH.

Содержание 1440E





























Отзывы: