ASEM BM1 Series, Руководство пользователя

Страница: 44 / 118

38 SECTION 4 – System Start-U
p
SATA Test Mode Test mode Enable / Disable [Enabled] [Disabled]
Aggressive LPM Support Enable PCH to aggressively enter link power state [Enabled] [Disabled]
SATA Port 1 [Not installed]
Software Preserve Unknown
Port 1 Enable or disable SATA Port [Enabled] [Disabled]
Mechanical Presence Switch Controls reporting if this port has Mechanical Presence Switch.
Note: requires hardware support.
[Enabled] [Disabled]
Spin Up Device If enabled for any of ports Staggerred Spin Up will be performed and only
the drives which have this option enabled will spin up at boot. Otherwise all
drives spin up at boot
[Enabled] [Disabled]
SATA Device Type Identify the SATA port is connected to Solid State Drive or Hard Disk Drive [Solid state drive]
SATA Port 1 DevSlp Enable/Disable SATA Port 1 DevSlp. Board rework for LP needed before ena-
ble.
[Enabled] [Disabled]
DITO Configuration Enable / Disable DITO Configuration [Enabled] [Disabled]
DITO Value Enable / Disable DITO Value [Enabled] [Disabled]
DM Value Enable / Disable DM Value [Enabled] [Disabled]
Table 24 - SATA Drives
4.3.6.14 Network configuration
BIOS setting Function Configuration options
Network configuration
LAN1 (I210) Enable/Disable Network controller connected to PCIe RP2 [Enabled] [Disabled]
LAN1 (I210) Boot ROM Enable/Disable Pxe Oprom for this ethernet controller. [Enabled] [Disabled]
Wake on LAN1 Enable/Disable Wake on LAN for this ethernet controller. [Enabled] [Disabled]
LAN2 (I210) Enable/Disable Network controller connected to PCIe RP3. [Enabled] [Disabled]
LAN2 (I210) Boot ROM Enable/Disable Pxe Oprom for this ethernet controller. [Enabled] [Disabled]
Wake on LAN2 Enable/Disable Wake on LAN for this ethernet controller. [Enabled] [Disabled]
Table 25 - Network configuration
4.3.6.15 USB configuration
BIOS setting Function Configuration options
USB configuration
XHCI Pre-Boot Driver Enable/Disable XHCI Pre-Boot Driver support. [Enabled] [Disabled]
xHCI Mode Once disabled, XHCI controller would be function disabled, none of the USB
devices are detectable and usable during boot and in OS. Do not disable it
unless for debug purpose. [Enabled] [Disabled]
USB VBUS UBUS should be ON in HOST node. It should be OFF in OTG device node. [On]
USB HSIC1 Support Enable/Disable USB HSIC1. [Enabled] [Disabled]
USB SSIC1 Support Enable/Disable USB HSIC1. [Enabled] [Disabled]
USB Port Disable Override Selectively Enable/Disable the corresponding USB port from reporting a De-
vice Connection to the controller. [Enabled] [Disabled]
XDCI Support Enable/Disable XDCI. [Enabled] [Disabled]
XHCI Disable Compliance Mode Options to disable XHCI Link Compliance Mode. Default is FALSE to not disa-
ble Compliance Node. Set TRUE to disable Compliance Mode. [FALSE]
USB HW MODE AFE Comparators Enable/Disable USB HW MODE AFE Comparators. [Enabled] [Disabled]
Table 26 - USB configuration
4.3.6.16 Miscellaneous Configuration
BIOS setting Function Configuration options
Miscellaneous Configuration
High Precision Timer Enable or Disable the High Precision Event Timer [Enabled] [Disabled]
8254 Clock Gating Enable or Disable 8254 Clock Gating. [Enabled] [Disabled]
State After G3
Specify what state to go to when power is re-applied after a power failure
(G3 state).
SO State: System will boot directly as soon as
power applied.
S5 State: System keeps in power-off state until
power button is pressed.
Power Button Debounce Mode Enable interrupt when PWRBTN# is asserted [Enabled] [Disabled]
Board Clock Spread Spectrum Enable Clock Chip’s Spread Spectrum feature [Enabled] [Disabled]
UART Interface Selection Select which UART interface to use [Internal UART]
BIOS Lock Enable/Disable the SC BIOS Lock Enable feature. Required to be enabled to
ensure SMM protection of flash.
[Enabled] [Disabled]
RTC Lock Enable will lock bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM [Enabled] [Disabled]
Flash Protection Range Registers (FPRR) Enable Flash Protection Range Registers. [Enabled] [Disabled]
TCO Lock Enable TCO and Lock Down TCO [Enabled] [Disabled]
DCI enable (HDCIEN) When DCI is Enabled, it is taken as user consent to enable the DCI which al-
lows debug over the USB3 interface. When Disabled, the host control is not
enabling DCI feature.
[Enabled] [Disabled]
DCI Auto Detect Enable When set to Auto Detect, it detects DCI being connected during BIOS post
tine and enables DCI. Else it disables DCI.
[Enabled] [Disabled]
GPIO Lock Enable to set GPIO Pad Configuration Lock for security [Enabled] [Disabled]
Table 27 - Miscellaneous Configuration
4.3.6.17 Boot
BIOS setting Function Configuration options
OS selection Select the target OS [Windows]
Silent Boot Disable console output and show logo if it is enabled [Enabled] [Disabled]