ASCO POWER TECHNOLOGIES 360 страница 9 Скачать руководство пользователя

Страница: 9 / 16

For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance

IO-70067

01/2020

ASCO 360 Surge Protective Device (SPD)

Electrical

Branch Circuit Overcurrent

Protection and Disconnect Means

Location of Surge Protective

Device (SPD)

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Use conductors rated for the Overcurrent Protection Device (OCPD) per

applicable codes.

• Use conductors rated for the application per applicable codes.

Failure to follow these instructions will result in death or serious injury.

A branch circuit Overcurrent Protection Device (OCPD) either in the form of

a circuit breaker or fuse must be provided for the ASCO 360 Type 2 device.

The branch circuit OCPD should either provide or include a disconnecting

means.

Since the current drawn by the ASCO 360 device during normal operation is

negligible, the ASCO 360 device can be connected to a dedicated, separate

branch circuit or connected to a suitable existing branch circuit.

When connected to a separate, dedicated branch circuit, the OCPD setting

must be selected to protect the conductors feeding the ASCO 360 device

per applicable state and local building codes.

UL 1449 Type 1 SPDs have been designed and approved for line side appli-

cations prior to the main service disconnect without supplemental overcur-

rent protection. Type 2 SPDs must be installed on the load side of the main

Overcurrent Protective Device (OCPD). All installations should either provide

or include a disconnecting means.

Locate the SPD as close as possible to the circuit mains being surge-limited

to minimize the wire length and optimize SPD performance. Avoid long wire

runs so that the device will perform as intended. To reduce the impedance

that the wire displays to surge currents, the phase, neutral, and ground

conductors (wye and high-leg delta configurations), or phase and ground

conductors (delta configurations), must be routed within the same conduit

and tightly bundled or twisted together to optimize device performance.

Avoid sharp bends in the conductors. See Figures 2 and 3.

DANGER

Содержание 360

















Результаты поиска

Содержание 360

Отзывы:

Похожие инструкции для 360

Бренды по названию

Популярные бренды

ASCO POWER TECHNOLOGIES 360, Руководство по установке и эксплуатации

Результаты поиска

Содержание 360

Отзывы:

Похожие инструкции для 360

Бренды по названию

Популярные бренды