AS MOTOR AS-751 RC Скачать руководство пользователя

Страница: 47 / 49

Page 47 / 49

FAULT LOCALISATION

Problem

Possible error

Possible solution

Motor runs with

Spark plug [*1]

Check distance or replace spark plug

the self-starter, but it

Wire damaged

Replace or repair wire

doesn’t start

Fuel filter clogged [*1]

Clean filter in carburettor

No fuel [p.26]

Refill fuel

Vacuum valve under fuel tank

Replace valve

Mower is in service position [p.14]

Put mower into working position

Defective NPN sensor [p.14]

Replace sensor

Distance too big for NPN sensor [p.14]

Adjust sensor – until diode is lit

Defective K2 relay [p.18]

Replace relay

Motor is not running

Battery discharged [p.25]

Charge the battery

from self-starter

No light in ECU lamp [*1]

Check 3 A fuse

Defective 30 A fuse

Replace 30 A fuse at rear of motor

Horn has not been activated [p.28]

Activate the horn

Defective 10A, 15 A, 3A fuses [p.18]

Replace the fuses

Motor is smoking

Air filter [p.24]

Clean / replace air filter

Mower will not start

Defective K3 relay [p.18]

Replace relay

Coupling defective

Replace coupling

Check wire and plug

Replace wire or plug

Defective drive belt for mower [p.39]

Replace belt

Defective drive belt for coupling [p.39]

Replace belt

Mower stops

Tilt sensor is active [p.35]

Move to a flatter area

Machine cannot run

Defective servomotor

Replace servomotor

Drive belt damaged [p.39]

Replace belt

Mower vibrates

Defective bearings

Replace bearings in mower

Dirt on flail bar

Clean flail bar

Flail missing [p.42]

Mount new flail

Worn flail [p.42]

Mount new flails

Machine has not enough

Damaged hydraulic pump

Replace pump

pulling power

Drive belt is slack [p.42]

Tighten belt

Hydraulic motor defective

Replace hydraulic motor

Oil is overheated [p.45]

Clean cooler, rear grate and guard grate

over the hydraulic pump

Not enough transmission oil [p.23]

Refill oil

No contact between

Machine outside operational range

Move remote control closer to receiver

remote control and

Disturbing radio signal [p.33]

Change frequency

receiver

Emergency stop of machine engaged

Disengage emergency stop

Defective 15A fuse [p.18]

Replace fuse

Emergency stop of remote control engaged

Disengage emergency stop

Machine makes noise

Defective flanged bearing by coupling

Replace bearing

Defective guard bearing

Replace bearing

Defective bearings in mower

Replace bearings

Poor mowing result

Worn flails [p.42]

Replace all flails

Driving speed too high

Lower the speed

Incorrect flail type [p.31]

Change flail type

Horn without function

Mower is in service position [p.14]

Put mower in working position

Defective 3A, 10A, 15A fuses [p.18]

Replace fuses

Horn automatically

Tilt sensor is activated [p.35]

Move to a flatter area

activated

Emergency stop of remote control activated,

emergency stop of machine not activated

Activate emergency stop of machine

[*1] See motor manual

Содержание AS-751 RC


















































Результаты поиска

Содержание AS-751 RC

Отзывы:

Похожие инструкции для AS-751 RC

Бренды по названию

Популярные бренды

AS MOTOR AS-751 RC, Руководство оператора и сервисная книжка

Результаты поиска

Содержание AS-751 RC

Отзывы:

Похожие инструкции для AS-751 RC

Бренды по названию

Популярные бренды