SPL 30 Owner's Manual v 1.1 ©2004 ARX®
SPL 30 Owner's Manual v 1.1 ©2004 ARX®
7
2
This symbol is intended to alert you to the presence of uninsulated dangerous
voltage within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
This symbol is intended to alert you to the presence of important operating
instructions contained in this owner's manual
WARNING SYMBOLS USED ON THIS EQUIPMENT
IMPORTANT - This self-powered loudspeaker
is designed to be connected ONLY to the AC
voltage ticked below
100 V AC, 50 - 60 Hz
!
It is essential that you check that this
voltage is correct for your area before
connecting it to AC power. Do not plug
power cable into AC power until the voltage
has been checked. If incorrect, contact your
ARX distributor.
Your warranty does not cover connecting to
the wrong AC voltage!
This product has a locking removable AC power lead.
To insert power cable, line up pins, insert connector and
twist to the right.
To remove, depress lever on top of the connector, twist to
the left, and pull out.
110 V AC, 50 - 60 Hz
220-240 V AC, 50 - 60 Hz
240 V AC, 50 - 60 Hz
SPL 30 Specifications
Frequency response
50Hz - 20KHz ±4dB
Loudspeaker type
Active 3 way with onboard amplification and
speaker processing
Low Frequency
Reflex loaded 15” 380mm 8 Ohm
Mid Frequency
Horn loaded 8” 200mm 8 Ohm
High Frequency
Horn loaded 2” throat driver 16 ohm
16 Ohm; FerroCooled
MF/HF Flare type
Flat front Consistent Beamwidth
Size
1010H x 545W x 515D, 7.5° taper to back
Weight
72 Kg
Dispersion
Nominal 60° H x 40° V
Input Connector
3 pin Female XLR, polarity Pin 2 +, Pin 3 –,
Pin 1 Ground
Input Impedance
44K Balanced (electronic)
Nominal input level
0dB for nominal rated amplifier outputs
Input Loop Connector
3 pin Male XLR, polarity Pin 2 +,
Pin 3 –, Pin 1 Ground
Crossover Frequency
500Hz, 2.5 KHz
Crossover Type
Active 24dB Linkwitz Riley Filter type
Highpass Filter
–3dB @ 50Hz 12dB Butterworth
Maximum SPL
134 peak, 127 continuous
Amplifier power
LF 400 Watts RMS 8 ohms, 575 peak
LF 200 Watts RMS 8 ohms, 350 peak
HF 150 Watts RMS 16 ohms, 200 peak
Amplifier type
Lateral Mosfet
THD
<.01%
Loudspeaker protection
ISC amplifier anti-clipping circuitry
Relay muted input
Relay switched output sensing DC and RF error
Status LEDs
AC power, HF Protect, LF Protect
AC Power
110V / 220V / 240V 50 / 60Hz
AC Power Input
Neutrik PowerCon type NAC 3 FCA
AC Power Loop
Neutrik PowerCon type NAC 3 FCB
AC Power protection
User resettable external circuit breaker
AC Wattage Max
1200 VA (1200 Watts)
Transformer type
Toroidal
Complies with 89/336/EEC EMC Directive, amended by
92/31/EEC and 93/68/EEC and meets the following
standards:EN 55013 : 1990, Sections 3.2 and 3.5 EN
55020 : 1988, Sections 4.3, 5.4, 6.2, 7.0, 8.0.
Complies with Australian Standard AS/N25 1053
