Arthrex DrillSaw Sports 400 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 52

background image

DrillSaw Sports 400™ System

User’s Guide

DFU-0253-4r0_fmt_en-US

Page 29 of

46

5

5

.

.

0

0

Cleaning and Disinfecting

The handpiece, attachments, aseptic battery housing, aseptic transfer kit and sterilizable
battery are supplied

non-sterile

and must be adequately cleaned, disinfected, and sterilized

prior to use or re-use.
Follow your country-specific directives, standards and guidelines for cleaning, disinfection
and sterilization.
Always wear proper PPE (Personal Protective Equipment) such as: gloves, eye protection,
face shields, gowns, etc.
To make cleaning and disinfecting easier, always clean and disinfect the Arthrex DrillSaw

Sports 400 System immediately after use; do not allow bodily fields and tissue to dry on any
of the system components.
With the exception of the aseptic battery pack and charging unit, Arthrex recommends

processing system components (handpiece, attachments, aseptic transfer kit , aseptic battery
housing and sterilizable battery) with an automated procedure using a washer/disinfector.

.

Remove any attachment and battery from the handpiece prior to cleaning.
Before charging the sterilizable battery, physically inspect the battery for damage and any
visible contamination.
Remove the aseptic battery pack from the aseptic battery housing, and clean and disinfect
the battery pack according to the instructions in Section 5.1.

Insert clean and dry battery onto charger and allow charging to full charge state.

Batteries should be stored on charger until immediately before the

sterilization process. Submerging a battery can

cause damage. Do not

submerge battery.

Do NOT autoclave the aseptic battery pack, or put it through the

Washer/Disinfector.

5.1

Aseptic Battery Pack

Do NOT autoclave the aseptic battery pack. It must be cleaned and disinfected after
use.
Do not immerse the aseptic battery pack or place it under running water as damage
to the components may occur.
Do not use disinfectants that contain chlorine or protein fixing effects. Use only those
cleaners/disinfecting agents that are certified by your facility.

«
...
33
34
35
36
37
...
»

Содержание DrillSaw Sports 400





















































Отзывы:

Нет отзывов

Похожие инструкции для DrillSaw Sports 400

Бренд: Malmbergs Страницы: 16

Бренд: Robitronic Страницы: 10

Бренд: Hi-Capacity Страницы: 3

Бренд: Ravpower Страницы: 13

Бренд: Radio Shack Страницы: 4

Бренд: Hamilton/Buhl Страницы: 8

UNIVERS U+ WB1-11-OCPP-LK7

Бренд: FTE Страницы: 40

Бренд: Victron energy Страницы: 51

Бренд: NEC Страницы: 71

Бренд: Hobbytech Страницы: 64

Terra AC wallbox UL

Бренд: ABB Страницы: 37

Бренд: ABB Страницы: 154

Terra AC Series

Бренд: ABB Страницы: 58

IMPRES 2 PMPN4350

Бренд: Motorola Страницы: 168

IMPRES Smart Energy System

Бренд: Motorola Страницы: 30

Бренд: Motorola Страницы: 56

Бренд: Motorola Страницы: 25

Бренд: Motorola Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды