ARTEX ELT 1000 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 62

background image

ARTEX PRODUCTS / ACR ELECTRONICS, INC.

DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL

ELT 1000 (P/N: A3-06-2749-1)

Y1-03-0259 Rev. U

Company Confidential

Page 45 of 62

5.

Buzzer

A.

Location

CAUTION:

PLACING THE BUZZER IN THE COCKPIT IS NOT RECOMMENDED DUE TO THE POTENTIAL
FOR DISTRACTION. THE BUZZER PRODUCES A LOUD, SIREN-TYPE SOUND WHEN THE ELT IS

ACTIVATED. SINCE THE BUZZER OPERATES IN TANDEM WITH THE COCKPIT LED, IT WOULD
ONLY SERVE AS A REDUNDANT WARNING INDICATOR IN THE COCKPIT.

1)

Select a suitable location for the buzzer.

NOTE:

The buzzer may be located anywhere in the aircraft; however, the recommended location is
near the ELT, as the buzzer is loud enough to be heard outside the aircraft when the engine(s)

is not running. When the engine(s) is running, the LED on the cockpit remote switch assembly
will warn the pilot the ELT is active.

B.

Installation

1)

Refer to AC 43.13-2 for fabrication and installation guidance.

2)

Fabricate a support bracket for the buzzer. See Figure 19 Buzzer Outline and Dimensions.

3)

Mount bracket and install buzzer. Either the panel mounting nut or flanges can be used to mount the buzzer.

Figure 19 Buzzer Outline and Dimensions

«
...
43
44
45
46
47
...
»

Содержание ELT 1000































































Отзывы:

Нет отзывов

Похожие инструкции для ELT 1000

SEPARIX-Control CT

Бренд: fafnir Страницы: 2

Бренд: Michell Instruments Страницы: 28

Бренд: Icom Страницы: 40

FMx5001M Series

Бренд: Jung Страницы: 10

Kotron RF 2-Wire Series

Бренд: Magnetrol Страницы: 12

Бренд: BEKA Страницы: 27

Бренд: AFi Страницы: 8

Бренд: COBHAM Страницы: 95

Бренд: Yaesu Страницы: 20

Бренд: Broadcast Electronics Страницы: 52

Бренд: devention Страницы: 84

Бренд: M-system Страницы: 5

Бренд: Harris Страницы: 9

Flexiva FAX 5KW

Бренд: Harris Broadcast Страницы: 168

Бренд: Icom Страницы: 112

Бренд: Icom Страницы: 68

Бренд: Icom Страницы: 126

Бренд: Icom Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды