manualshive.com logo in svg

ARTEX AIRCRAFT SUPPLIES ME406, Описание, эксплуатация, установка и техническое обслуживание

Поделиться
Скачать
ARTEX AIRCRAFT SUPPLIES ME406 Скачать руководство пользователя страница 18

ARTEX AIRCRAFT SUPPLIES, INC. 

570-1600 

The mounting location must conform to the requirements of RTCA DO-204 and AC 43.13. DO-
204 Sec 3.1.8 states: 

“The ELT shall be mounted to primary aircraft load carrying structures such as 

trusses, bulkheads  longerons, spars, o  floor beams (not aircraf  skin). The 

mounts shall have a maximum static local deflection no greater than 2.5 mm 

(0.1 in.) when a force of 450 Newtons (100 lbs) is applied to the mount in the 

most flexible direction. Deflection measurements shall be made with reference 

to another part of the airframe not less than 0.3 meters (1-foot) nor more than 

1.0 m (three feet) from the mounting location.” 

,

r

t

Mount the ELT so that the longitudinal axis of the ELT (the axis extending through the longest 
dimension) is aligned with that of the aircraft within 10º.  The ELT mount can be rotated about 
the longitudinal axis, i.e., the ELT can be mounted on the floor, walls or overhead, so long as it 
‘points’ to the front of the aircraft. 

Using the template provided, mark and drill four mounting holes using a #19 (0.1660”/ 4.2mm) 
drill bit. Install the mounting tray.  Artex suggests using the outermost mounting hole-pattern 
on the template for minimum flexure of the mounting tray.  Use the 8-32 X 5/8” Phillips, pan-
head screws, nuts and flat washers provided.  

Refer to paragraph 2.10 (page 28) for specific information regarding helicopter installations. 

 

Page 10 of 60 

Содержание ME406





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды