manualshive.com logo in svg

Artesyn ATCA-F140, Инструкция по установке и эксплуатации

Поделиться
Скачать
Artesyn ATCA-F140 Скачать руководство пользователя страница 46

Hardware Preparation and Installation

ATCA-F140 Installation and Use (6806800M67J

)

46

2.9

Installing and Removing QSFP+ Modules

This section describes the installation and removal process of the Quad Small Form-factor 
Pluggable Plus (QSFP+) transceiver modules.

Eye Damage

Optical QSFP+ modules may emit laser radiation when no cable is connected.

Avoid staring into open apertures to avoid damage to your eyes.

Personal Injury and Damage of the board, RTM and QSFP+ Modules

Installing and using QSFP+ modules which are not fully certified and which do not meet 
all relevant safety standards may damage the board, RTM and the QSFP+ modules and 
may lead to personal injury.

Only use and install QSFP+ modules which are fully certified and which meet all relevant 
safety standards.

Personal Injury

Optical QSFP+ modules may be classified as laser products. When installing and using 
any of these QSFP+ modules, the regulations which correspond to the respective laser 
class apply to the whole board and RTM. Non-compliance with these regulations may 
lead to personal injury.

When installing and using optical QSFP+ modules which are classified as laser products, 
make sure to comply to the respective regulations.

The maximum power consumption of each QSFP+ module should be 2W.

Содержание ATCA-F140











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды