background image

DLC910 Function Module Installation and Operations Manual 

7

 

Configuring the Module with DigiLink Manager

 

Cabling the DLC910 Module

This section describes how to cable the external connections of the DLC910 module, which can receive and 

transmit external signals over its BNCs and SFPs. The cabling configuration that you use depends on your 

application.

Figure 5. 

DLC910 BNC Connectors and SFP Sockets

Cabling the BNC Connections

To connect to the BNC connectors on the DLC910, use a high quality 75 Ohm precision video coax cable, such 

as Belden 1694A cable.
To cable the electrical connections, perform the following tasks:

• 

Input signal—Connect the coax cable to the DLC910 receive connector (IN) and the source device’s 

electrical transmit connector.

• 

Output signal—Connect the coax cable to the DLC910 transmit connector (OUT) and the destination 

device’s electrical receive connector.

Cabling the SFP Connections

The type of cable connection that you make to the SFPs depends upon the type of SFP that you use as 

described in the

”Supported SFP Types”  section on page 3

.

When using optical SFPs, use a single mode fiber when connecting to the LC connectors of the SFPs and cover 

any unused optical port to keep the port clean.

Configuring the Module with DigiLink Manager

You configure the DLC910 module operation using the DigiLink Manager (DL Manager) element management 

system and the module’s configuration page. 

Prerequisites

To configure the DLC910 module, you must access the DL Manager that manages the module. For details 

about accessing and setting up DL Manager, see the 

DigiLink Manager Setup and Operations Manual

.

To configure the DLC910 module operation, perform the following steps:

1.  From a browser window, enter the IP address of the DL Manager that manages the module.

The Home page displays.

Содержание DigiLink DLC910





























Отзывы: