background image

* Size rounded off to the nearest foot

BUILDING DIMENSIONS

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

709831110

Model No.

     EN106

NW106

697. 68206-A

Owner's Manual & Assembly Instructions

       AZ01

Exterior Dimensions                     Interior Dimensions                    Door

       *Approx.                 Base                   (Roof Edge to Roof Edge)                      (Wall to Wall)                       Opening
           Size                    Size                  Width       Depth       Height           Width       Depth      Height       Width     Height

         10' x 6'

      121" x 68 3/4"          123 1/4"     71 1/4"       70 7/8"       118 1/4"        66"        69 5/8"       55 1/2"        58"

3,0 m x 1,7 m      307,3 cm x 174,6 cm     313,1 cm    181,0 cm     180,0 cm           300,4 cm      167,6 cm   176,8 cm       141,0 cm    147,3 cm

  Storage Area:    54 Sq. Ft.

294 Cu. Ft.

                5,0 m

2

             8,3 m

3

Missing Parts, Questions on Assembly?

Call:  1-800-851-1085

Do not return to dealer, they are not

equipped to handle your requests.

Содержание 697. 68206-A

































Отзывы: