background image

 3719     Door Handle Brace (2)

 10475 Right and Left Doors (2)

 10497 Horizontal Door Brace (4) 

 6278    Vertical Door Brace (2)

 Parts Needed For 

Door Assembly

Step 19

SO32

The steps on this page tell how to 
assemble the right door. You will per-
form exactly the same procedures for 
the left door. Each bolt and screw in 
the door requires a washer. Proceed 
as follows:

Attach the door handle brace 

and  handle  to the door  with 1 bolt 
as shown. Don't tighten the bolt yet.

Swing the door handle brace up 

to the hole on the center of the door 
and insert a screw.

Hold the vertical door brace 

against the center of the inside sur-
face of the door and turn the screw 
to hold the vertical door brace and 
door handle brace in place.  Fasten 
to door above and below center 
connection using 2 screws.

Insert a second bolt in the door 

handle and tighten both bolts.

Put a horizontal door brace onto 

the top edge and bottom edge and 
fasten with 1 bolt in the center.

Attach the lower door guides and 

bolts as shown.

Repeat steps 1 through 6 for the 

left door.

STEP

5

4

3

10475 

 

 Right Door

66382

66382  

10497

66045

3719

66382

END VIEW

SHOWING:

Horizontal

Door Brace

Door

Washer

Guide

6278

6278

3719

10475 

  

Left Door

66045

66045

3719

STEP

1

STEP

2

STEP

6

10497

10497

10497

STEP

STEP

66382  

66382  

6278

32

Содержание CG1012





































Отзывы: