ARRI WRC-1 Скачать руководство пользователя страница 26

Страница: 26 / 196

5.1.2 WRC mode

In this mode the WRC-1 offers convenient and quick access
to camera functions and additional programming options.

• Set the sliding switch on the camera from NORM to

PS/CCU

➪

photo

The display of the WRC-1 flashes with the warning
‘not PSCCU’ until the camera’s sliding switch is set to
PS/CCU.

• Set the WRC/CAM sliding switch to WRC

➪

photo

• The IRIS sliding switch governs whether the WRC-1

activates its control over the iris motor (IRIS ‘ON’), or
whether a connected iris motor is controlled by
another unit (IRIS ‘OFF’). This must be set before
switching on the WRC-1.

If the iris control is not activated (IRIS sliding switch
‘OFF’), the OPEN button serves as the PHASE button on
the camera

➪

photo

Forward or reverse run is set in CAM mode and in the
same way as on the camera itself.

sliding switch NORM / PS/CCU

READY-LED

WRC/CAM sliding switch

IRIS sliding switch

OPEN/PHASE-

button

Operation

Содержание WRC-1





































































































































































































Результаты поиска

Содержание WRC-1

Отзывы:

Бренды по названию

Популярные бренды

ARRI WRC-1, Инструкция по эксплуатации

Результаты поиска

Содержание WRC-1

Отзывы:

Бренды по названию

Популярные бренды