manualshive.com logo in svg

ARRI UMC-4, Руководство пользователя

Поделиться
Скачать
ARRI UMC-4 Скачать руководство пользователя страница 9

 

 
Universal Motor Controller UMC-4

 – User Manual – V 02/2015 

Page 9 of 54 

For Your Safety 

Always keep this document on hand. It should be read, understood and 
observed by all persons using the Universal Motor Controller UMC-4. All 
other products must be handled as prescribed by their manufacturers. 

Risk Levels and Alert Symbols 

Safety warnings, safety alert symbols, and signal words in these 
instructions indicate different risk levels: 

This symbol alerts you to personal injury hazards or damage to the 

equipment. Obey all warnings that follow this symbol to avoid possible 
injury or death or damage to the equipment. 

This symbol alerts you to electrical hazards. Obey all warnings that 

follow this symbol to avoid possible injury or death. 

DANGER! 

Indicates an imminent, hazardous situation which, if not avoided, will result 
in death or serious injury. 

NOTICE: Explains practices not related to physical injury. The safety alert 
symbol is not used with this signal word. 

 

Note:  Provides additional information to clarify or simplify a procedure. 

 

 

Содержание UMC-4























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды