ARRI cforce plus Скачать руководство пользователя страница 3

 

3

Disclaimer

Before using the products described in this manual, be sure to read

and understand all the respective instructions.
The ARRI cforce plus Lens Motor is only available to commercial

customers. By utilization, the customer agrees that the cforce plus

Lens Motor or other components of the system are deployed for

commercial use only. Otherwise the customer must contact ARRI

before utilization.
While ARRI endeavors to enhance the quality, reliability and safety

of their products, customers agree and acknowledge that the

possibility of defects thereof cannot be eliminated entirely. To

minimize the risk of damage to property or injury (including death)

to persons arising from defects in the products, customers must

incorporate sufficient safety measures in their work with the system

and heed the stated canonic use.
ARRI or its subsidiaries do not assume any responsibility for losses

incurred due to improper handling or configuration of the cforce

plus Lens Motor or other system components.
ARRI assumes no responsibility for any errors that may appear in

this document. The information is subject to change without notice.
For product specification changes after this manual was published,

refer to the latest published ARRI data sheets or release notes,

etc., for the most up-to-date specifications. Not all products and/

or types are available in every country. Please check with an ARRI

sales representative for availability and additional information.
Neither ARRI nor its subsidiaries assume any liability for

infringement of patents, copyrights or other intellectual property

rights of third parties by or arising from the use of ARRI products or

any other liability arising from the use of such products. No license,

express, implied or otherwise, is granted under any patents,

copyrights or other intellectual property right of ARRI or others.
ARRI or its subsidiaries expressly exclude any liability, warranty,

demand or other obligation for any claim, representation, cause,

action, or whatsoever, express or implied, whether in contract or

not, including negligence, or incorporated in terms and conditions,

whether by statue, law or otherwise. In no event shall ARRI or its

subsidiaries be liable for or have a remedy for recovery of any

special, direct, indirect, incidental, or consequential damages,

including, but not limited to lost profits, lost savings, lost revenues

Содержание cforce plus





























Отзывы: