Set description
Operation
x2
Items included in the package:
1 -
Flashlight
2 -
Clip
3 -
2 rubber rings
4 -
Rubber grip
5 -
Lanyard
x2
6 -
Holster
7 -
Spare rubber button
8 -
2 spare O-rings
9 -
User manual
1
2
3
4
5
6
7
8
9
Predator
x10
x1
5
Change Hunting/Tactical settings
Unscrew & Tighten up x10
Half Press & Release (no click)
1/2
1/2
Additional modes
Click x1
Unscrew to 1/8
Cycling through Additional modes
Turbo
гд
Main2
Strobe2
гд
Strobe1
Click x1
Tighten up
Turbo
Change Constant modes
Unscrew & Tighten up
Constant light
Strobe
Change Strobe modes
Tighten up & Unscrew
How to change Turbo1 & Turbo2
Half Press & Release (no click)
Firefly1
Firefly2
Main1
Main2
Main3
Initial Service
1.
2.
3.
To set/replace batteries:
1.
Unscrew the tailcap.
2.
Place the batteries with the positive contact (+) facing the head of the flashlight.
3.
Adjust the tailcap and tighten it as far as it can go.
ь
Y
our
flashlight
can inconsiderably differ from the pictures in the manual.
ь
The producer reserves the right to change the package at his own discretion without modifying this manual
.
We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable)
can leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries
in
then
use new and
high-
quality batteries
and
store the flashlight in acceptable for batteries operational temperature and revise the batteries'
state at least once a month. If you have noticed any signs of batteries' defects
then
withdraw them from the flashlight and utilize. It is also
recommended to replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.
Active temperature control.
T
he flashlight
can quickly heat up
in
Turbo
mode
. W
hen
the temperature becomes +60
°
C –
the
brightness decreases by
small steps
. After cooling-down
(
provided that battery voltage is sufficient
)
the brightness increases to the
Turbo
mode again. This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In conditions of good
air-cooling the flashlight delivers light
without stepping down
even in
Turbo
mode. There are no preset timers for stepping, but real-
time
active temperature measurements.
Momentary on
– any mode
switched
on
by half-pressing of the
button
(no click!)
and active till the button is released.
It is s
uitable
for giving signals by short button pressings.
Click the button to
switch the light on permanently.
Hunting settings
– comfortable modes for hunting.
It’s
set by
default.
Turbo mode (when the head is
tightened
up) and
Additional modes with constant light (changed by click
with the
head
unscrewed to 1/8).
Remote switch can be used in Turbo.
Tactical
settings
– made for Special forces and Airsoft. Constant
light (when the head is
tightened
up) and Strobe mode (when the
head is unscrewed to 1/8).
There are 2 Strobe modes and 2
Constant light modes for selection. Remote switch can be used in
ANY mode.
How to change the settings from one to another
– unscrew and
tighten up the head of the flashlight at least 10 times (while
rotation you will change the modes). The pause must be <1 sec.
Hunting settings:
Turbo
.
Tighten the head of the flashlight if it is
unscrewed
.
First full
click
of the button turns the light on.
Second full
click
turns it off.
Additional
modes (2 F 3 Main).
If the head of the flashlight is
tightened
up
,
unscrew
it for 1/8 of a circle.
F
ull
click
of the button
turns the light on at
the last used Additional mode
.
Cycling through Additional modes.
To switch the
mode
turn the
flashlight o
ff
and o
n
(
by full
click or half-pressing).
The
modes
switch cyclically
: Firefly1 – Firefly2 – Main1 – Main2 – Main3.
Tactical settings:
Constant light.
Tighten the head of the flashlight if it is
unscrewed
.
First full
click
of the button turns
constant
light on.
Second full
click
turns it off.
Also you can switch it on
by half-pressing of the
button
(no click).
Strobe.
If the head
is tightened
up
,
unscrew
it for 1/8 of a circle.
First full
click
of the button turns
Strobe
on.
Second full
click
turns
it off.
Also you can switch it on
by half-pressing of the button
(no
click).
Change Constant modes.
T
he head is tightened
up:
unscrew
it for
1/8
and tighten up again – Turbo and Main2 will switch cyclically
.
Change Strobe modes.
T
he head is
unscrewed:
t
ighten
up and
unscrew
it for 1/8
again – Strobe1 and Strobe2 will switch
cyclically
.
How to change Turbo1 & Turbo2.
There are two Turbo modes. You
will use only one, but can select which one. Turbo2 is boost mode
for maximal brightness and
set by default.
Turbo1 is constant
brightness mode (more powerful than Main modes).
Half press & release the button (without click) at least 15 times.
The flashlight must be switched on at the end of these actions.
The
light will flash 1 or 2 times to show the number of Turbo chosen.
Automemorizing.
After switching off the last used Mode is
memorized for quick 1-click access at next switching on.
Lock-out function.
Unscrew the tailcap to 1/4 for the protection
from accidental switching on.
Low Battery Indication.
If the brightness is <25% from the nominal
value, the LED flashes 2 times
ONCE (after 30sec from switching
on). If you are not sure if it flashed or not switch the flashlight off
and on: in case the battery is low flashes will repeat. Light output
decreases to Firefly mode at critical level.
