manualshive.com logo in svg

Armstrong EHU-700 Series, Руководство по установке и обслуживанию

Поделиться
Скачать
Armstrong EHU-700 Series Скачать руководство пользователя страница 7

6)   WATER FILL SUPPLY

Connect the unit to the building water supply (25 to 125 psig pressure). Install a shut-off valve 
near the humidifier. Connect the water supply to the 3/8" tube compression fitting on the fill valve
adaptor.

NOTE: 

ORDINARY (POTABLE) TAP WATER IS RECOMMENDED. IF POTABLE WATER IS NOT

AVAILABLE, CONSULT THE FACTORY (SEE "WATER QUALITY AND TREATMENT SECTION OF
THIS MANUAL, PAGE 23, FOR MORE INFORMATION). DO NOT USE BRACKISH OR CONTAMI-
NATED WATER.

7) CONNECT 

DRAIN

Connect to a suitable waste draining 
system. Use the clear drain hose provided 
and a 1" copper pipe (Figure 7-1), pitched 
1"per foot. The drain water may be as hot 
as 160°F. Drain it where it will not present a 
hazard to personnel. An air gap to prevent 
backflow is required if drain water is
required to be less than 140°F, use 
of Temp-R-Drain will be required.

8) INSTALL THE 

STEAM 

DISPERSION TUBE NOTE: Please 
contact factory for duct applications 
offering high static pressures (>4"WC).

a.    Verify that the proper length and type of 

steam dispersion tube has been selected: 
See Chart 7-1 for proper dispersion tube
lengths. The low capacity dispersion 
tube (Figure 7-2) is sloped toward the 
generator to allow for gravity drainage. 
On applications where the humidifier output
capacity is greater than 40 Ibs/hr, a high 
capacity tube with a ½"O.D. drain tube 
must be used (Figure 7-3). Drain tube must 
have minimum 6" water seal (see Fig. 8-3).

b.    Select a location on the duct that provides

adequate length for vapor mixing and the
shortest connection length for vapor
mixing and the shortest connection length 
to the humidifier. Preferably the location 
should be 6" downstream and/or 10 feet    
upstream from any dampers, vanes, bends
in the duct, or controllers (i.e. high limit stat).
See page 10 for details. Do not install the 
dispersion tube into ducts in which airflow 
exceeds 2,000 fpm. Do not restrict airflow in 
ducts with a depth of 8 inches or less. 

Avoid placing manifold in downward, high 

velocity air flow as dynamic air pressure will
restrict steam flow.

7

1" I.D. Clear Hose
Supplied with Unit

Fit Hose Inside
1-1/2" Pipe

1" or Larger 
Copper Pipe

L

For Steam Capacity

40 lb/hr or Less

5.25

6.00

6.00

Ø

.22 

4 Places

5.25

Ø

1.75 

Hole in Duct

6.00

6.00

R.88

3.50

1.50

Ø

.22

4 Places

1.00

5.25

R.37

5.25

2.00

3.50

For Steam Capacity

Above 40 lb/hr

Hole in Duct

L

Figure 7-1

Chart 7-1. Selecting Proper Steam Dispersion Tube

Steam

Steam Disp. 

Duct Width

Weight

Disp. Tube

Tube Length

Min.

Max.

Model No.

in

mm

in

mm

in

mm

lb

kg

D-1

12

304

11

279

16

406

3

1.4

D-1.5

18

457

17

432

22

559

3

1.4

D-2

24

609

23

584

34

864

4

2

D-3

36

914

35

889

46

1168

6

3

D-4

48

1219

47

1194

58

1473

8

3.6

D-5

60

1524

59

1499

70

1778

9

4

D-6

72

1829

71

1803

82

2083

10

4.5

D-7

84

2133

83

2108

94

2388

11

5

D-8

96

2438

95

2413

106

2693

12

5.5

D-9

108

2743

107

2718

118

2998

13

6

D-10

120

3048

119

3023

130

3302

14

6.4

Figure 7-2

Figure 7-3

Содержание EHU-700 Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды