background image

507838-01

Issue 1813

Page 10 of 19

3.  With only the blower motor running and the evaporator 

coil dry, observe the manometer reading. Adjust blower 

motor speed to deliver the air desired according to the 

job requirements.

4.  For best air performance external static pressure drop 

must not exceed 0.5” W.C. (1.2 kPa). Refer to blower 

data tables for CFM and external static.

5.  Seal around the hole when the check is complete.

Adjusting Blower Speed

Motor Speed Taps

NOTE: Motor is programmed for a 45-second delayed OFF 

on all speed taps except TAP #1 (continuous fan speed).

Table 4 lists the recommended factory blower speed tap 

selections for BCE7E series units.

Operation

BCE7E

Outdoor Unit

Tap

Cooling

All Sizes

Air conditioner

3

Heat pump

3

Heating*

Air conditioner with electric 

heat only

4

Heat pump with electric 

heat

4

* Minimum setting for heat

Table 4. Recommended Blower Speed Tap Selection

These settings are for nominal tonnage match-ups with 

the BCE7E units. When matched with other sizes, it is 

recommended that the CFM be adjusted to approximately 

400 CFM per ton.

To change blower motor speed tap remove the speed 

tap from Y2 on the terminal strip and insert the desired 

speed tap. Use the Blower Data tables for the desired CFM 

setting.

The  high-efficiency  programmable  motor  features 

programmed electronic braking. The integral control 

brakes the motor near the end of the supply blower 

operation, allowing the motor to maintain a more 

controlled ramping shut-down.

 IMPORTANT

Tap

Operation

Remarks

1

Continuous or low-

speed fan (for two-

speed heat pumps 

or AC units)

Continuous fan speed is 

energized (24V input to G) 

when either G or Y1 has a 

24V signal (24V input from 

Y1 passes through the room 

thermostat’s Fan Automatic 

contacts to the G terminal).

2

Low-speed 

operation on high-

static system

CFM set at 1/2 ton less than 

nominal of unit (e.g. 3-ton set at 

1000 CFM).

3

Cooling speed 

setting

CFM set at 400 cfm per nominal 

ton at ARI minimum static 

allowed, as follows:
1.5 to 2.0 ton - 0.10
2.5 to 3.5 ton - 0.15
4 to 5 ton - 0.20

4

Heat pump with 

electric heat

CFM set at 400 cfm per nominal 

ton at .4 static. Energized when 

electric heat element has a call 

for heat.

5

High-static 

applications

CFM set at 400 cfm per nominal 

ton at .8 static.

Table 5. Motor Speed Taps

Содержание BCE7E Series




















Отзывы: